Electronic Components Datasheet Search |
|
ERA2AED102X Datasheet(PDF) 3 Page - Panasonic Battery Group |
|
ERA2AED102X Datasheet(HTML) 3 Page - Panasonic Battery Group |
3 / 4 page Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Metal Film Chip Resistors, High Reliability Type Chip Resistor a b Preheating Peak Heating Time Type (inches) Dimensions (mm) ab c ERA2A(0402) 0.5 to 0.6 1.4 to 1.6 0.4 to 0.6 ERA3A(0603) 0.7 to 0.9 2 to 2.2 0.8 to 1 ERA6A(0805) 1 to 1.4 3.2 to 3.8 0.9 to 1.4 ERA8A(1206) 2 to 2.4 4.4 to 5.0 1.2 to 1.8 Temperature Time Preheating 140 °C to 160 °C 60 s to 120 s Main heating Above 200 °C 30 s to 40 s Peak 235 ± 5 °C max. 10 s Temperature Time Preheating 150 °C to 180 °C 60 s to 120 s Main heating Above 230 °C 30 s to 40 s Peak max. 260 °C max. 10 s For soldering For lead-free soldering Temperature TimeTemperature Time Preheating 140 °C to 180 °C 60 s to 120 s 150 °C to 180 °C 60 s to 120 s Soldering 245 ± 5 °C 20 s to 30 s max. 260 °C max. 10 s ■ Recommended Soldering Conditions Recommendations and precautions are described below. ● Recommended soldering conditions for reflow For soldering (Example : Sn/Pb) For lead-free soldering (Example : Sn/Ag/Cu) ● Recommended soldering conditions for flow In case of flow soldering, the land width must be smaller than the Chip Resistor width to properly control the solder amount properly. Generally, the land width should be 0.7 to 0.8 times (W) of the width of chip resistor. In case of reflow soldering, solder amount can be adjusted, therefore the land width should be set to 1.0 to 1.3 times chip resistor width (W). ■ Recommended Land Pattern Safety Precautions The following are precautions for individual products. Please also refer to the precautions common to Fixed Resistors shown on page ER2 of this catalog. 1. Keep the rated power and ambient temperature within the specified derating curve. * When positioning and mounting Metal Film Chip Resistors (hereafter called the resistors), make allowance for the effect of heat generated through close contact between the resistors and neighboring components and for the temperature rise of adjacent heat-generating components. 2. If a transient load (heavy load in a short time) like a pulse is expected to be applied, check and evaluate the operations of the resistors when installed in your products before use. When applying pulses to the resistors, keep the pulse peak within the rated voltage. 3. Do not use halogen-based or other high-activity flux. Otherwise, the residue may impair the resistors' performance and/or reliability. 4. When soldering with a soldering iron, never touch the resistors' bodies with the tip of the soldering iron. When using a soldering iron with a high temperature tip, finish soldering as quickly as possible (within three seconds at 350 °C max.). 5. As the amount of applied solder becomes larger, the mechanical stress applied to the resistors increases, causing problems such as cracks and faulty characteristics. Avoid applying an excessive amount of solder. 6. When the resistors' protective coatings are chipped, flawed, or removed, the characteristics of the resistors may be impaired. Take special care not to apply mechanical shock during automatic mounting or cause damage during handling of the boards with the resistors mounted. 7. Do not apply shock to the resistors or pinch them with a hard tool (e.g. pliers and tweezers). Otherwise, the resistors' protective coatings and bodies may be chipped, affecting their performance. 8. Avoid excessive bending of printed circuit boards in order to protect the resistors from abnormal stress. 9. Do not immerse the resistors in solvent for a long time. Before using solvent, carefully check the effects of immersion. · Reflow soldering shall be performed a maximum of two times. · Please contact us for additional information when used in conditions other than those specified. · Please measure the temperature of the terminals and study every kind of solder and printed circuit board for solderability before actual use. Feb. 2009 |
Similar Part No. - ERA2AED102X |
|
Similar Description - ERA2AED102X |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |