 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
AS2535T Datasheet(PDF) 7 Page - ams AG |
|
||||||||||||||||||||||||||||||
AS2535T Datasheet(HTML) 7 Page - ams AG |
|
|
7 / 26 page  Data She et AS25 33-36 austriamicrosystems Revision 8.10 Page 6 of 25 Transmit The gain of the transmit path is 37 dB for 600 Ω line termination from M1/M2 to LS (see test circuit Figure 9). The microphone input is differential with an input impedance of 20 k Ω. The soft clip circuit limits the output voltage at LI to 2VPEAK (see Figure 11). The attack time is 30 µs/6 dB and the decay time is 20 ms/6 dB. When mute is active, during dialing or after pressing the P/M key, the gain reduced by > 60 dB. Receive The gain of the receive path is 3 dB for 600 Ω line termination (test circuit Figure 9). The receive input the differential signal of RI and STB. When mute is active during dialing the gain is reduced by > 60 dB. During DTMF dialing a MF comfort tone is applied to the receiver. The comfort tone is the DTMF signal with level that is -30 dB relative to the line signal. The receive gain can be changed by pressing the volume keys. The VOL key gives a +5.4 dB boost and has a toggle function, i.e. repressing the key resets the gain to default. As an alternative the +/– keys can be used. The + key increases the gain by 8.1 dB in 3 steps and the – key decreases the gain by 5.4 dB in 2 steps (total range 13.5 dB). On AS2533/35 the volume is reset to default by next off-hook and on AS2534/36 the volume setting will remain at last setting. A POR will always reset the volume to default. The soft clip circuit limits the voltage at the receive output (RO) to 1V PEAK (see Figure 10). It prevents harsh distortion and acoustic shock. Sidetone A good sidetone cancellation is achieved by using the following equation: 1 2 Z Z Z Z BAL Line = The sidetone cancellation signal is applied to the STB input. Line Loss Compensation The line loss compensation is a pin option. When it is activated, the transmit and receive gains are decreased by 6 dB at line currents from 20 to 50 mA when LLC = AGND and 45 to 75 mA when LLC = high (@ R1 = 30 Ω). The line loss compensation is disabled when LLC = low (see Figure 6 and Figure 7). Dialing Functions Valid Keys The key scanning is enabled when HS/DPN is pulled high and VDD is above VREF. A valid key is detected from the keyboard by connecting the appropriate row to the column (RON < 1 k Ω). This can be done using an n x m keyboard matrix with single contacts. Four diodes are used to extend the number of rows (see keyboard arrangement fig. 2). It is also possible to connect a microcontroller to the rows and columns (see application note AN3010). P/M and MT Key The P/M key is used to enter the Program/Mute state. Depressing the P/M key mutes the speech circuit and the device is in program state. Repressing the P/M key deactivates the mute and program state (toggle function).The MT key works in similar way, but has no program function. When program/mute is activated, the LED indication is turned on (flashing: 80 ms 'on' and 1 sec 'off'). Dial Mode Selection The default mode (LD or MF) can be selected by the mode pin. When default LD mode is selected, a temporary change to MF can be invoked by pressing T/P key (not AS2535) or the * key (when mode pin = row 5, the MF tone is generated with the first * key entry). The circuit will revert to LD by repression the T/P key (not AS2535) or by pressing the R (R1, R2 or R3) key or by next on-hook. When MF mode is selected by the mode pin, the circuit can not be changed temporary to LD but will remain in MF mode. Centrex Keys (not AS2535) The alphanumeric keys accommodate easy use of centrex services. The A, B, C and D keys are only valid in MF mode (including temporary MF) and are not storable. Pressing one of these keys will invoke the appropriate MF tones to be transmitted. The centrex keys are not stored in the RAM, and subsequently entered digits are buffered in FIFO. ZLI ZBA Z1 Z2 Figure 5 Side Tone Balance |
Similar Part No. - AS2535T |
|
Similar Description - AS2535T |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
