Electronic Components Datasheet Search
  English  ▼
ALLDATASHEET.NET

X  

CAT524JITE13 Datasheet(PDF) 5 Page - Catalyst Semiconductor

Part # CAT524JITE13
Description  Configured Digitally Programmable Potentiometer (DPP??: Programmable Voltage Applications
Download  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  CATALYST [Catalyst Semiconductor]
Direct Link  http://www.catalyst-semiconductor.com
Logo CATALYST - Catalyst Semiconductor

CAT524JITE13 Datasheet(HTML) 5 Page - Catalyst Semiconductor

  CAT524JITE13 Datasheet HTML 1Page - Catalyst Semiconductor CAT524JITE13 Datasheet HTML 2Page - Catalyst Semiconductor CAT524JITE13 Datasheet HTML 3Page - Catalyst Semiconductor CAT524JITE13 Datasheet HTML 4Page - Catalyst Semiconductor CAT524JITE13 Datasheet HTML 5Page - Catalyst Semiconductor CAT524JITE13 Datasheet HTML 6Page - Catalyst Semiconductor CAT524JITE13 Datasheet HTML 7Page - Catalyst Semiconductor CAT524JITE13 Datasheet HTML 8Page - Catalyst Semiconductor CAT524JITE13 Datasheet HTML 9Page - Catalyst Semiconductor Next Button
Zoom Inzoom in Zoom Outzoom out
 5 / 12 page
background image
CAT524
5
Doc. No. 25076-00 Rev. 4/01
PIN DESCRIPTION
Pin
Name
Function
1VDD
Power supply positive.
2
CLK
Clock input pin.Clock input pin.
3
RDY/
BSY
Ready/Busy Output
4
CS
Chip Select
5
DI
Serial data input pin.
6
DO
Serial data output pin.
7
PROG
EEPROM Programming Enable
Input
8
GND
Power supply ground.
9VREFL
Minimum DAC output voltage.
10
VOUT4
DAC output channel 4.
11
VOUT3
DAC output channel 3.
12
VOUT2
DAC output channel 2.
13
VOUT1
DAC output channel 1.
14
VREFH
Maximum DAC output voltage.
DEVICE OPERATION
The CAT524 is a quad 8-bit Digital to Analog Converter
(DAC) whose outputs can be programmed to any one of
256 individual voltage steps. Once programmed, these
output settings are retained in non-volatile EEPROM
memory and will not be lost when power is removed from
the chip. Upon power up the DACs return to the settings
stored in EEPROM memory. Each DAC can be written
to and read from independently without effecting the
output voltage during the read or write cycle. Each
output can also be temporarily adjusted without chang-
ing the stored output setting, which is useful for testing
new output settings before storing them in memory.
DIGITAL INTERFACE
The CAT524 employs a standard 3 wire serial control
interface consisting of Clock (CLK), Chip Select (CS)
and Data In (DI) inputs. For all operations, address and
data are shifted in LSB first. In addition, all digital data
must be preceded by a logic “1” as a start bit. The DAC
address and data are clocked into the DI pin on the
clock’s rising edge. When sending multiple blocks of
information a minimum of two clock cycles is required
between the last block sent and the next start bit.
Multiple devices may share a common input data line by
selectively activating the CS control of the desired IC.
Data Outputs (DO) can also share a common line
because the DO pin is Tri-Stated and returns to a high
impedance when not in use.
CHIP SELECT
Chip Select (CS) enables and disables the CAT524’s
read and write operations. When CS is high data may be
read to or from the chip, and the Data Output (DO) pin is
active. Data loaded into the DAC control registers will
remain in effect until CS goes low. Bringing CS to a logic
low returns all DAC outputs to the settings stored in
EEPROM memory and switches DO to its high imped-
ance Tri-State mode.
Because CS functions like a reset the CS pin has been
equipped with a 30 ns to 90 ns filter circuit to prevent
noise spikes from causing unwanted resets and the loss
of volatile data.
CLOCK
The CAT524’s clock controls both data flow in and out of
the IC and EEPROM memory cell programming. Serial
data is shifted into the DI pin and out of the DO pin on the
clock’s rising edge. While it is not necessary for the clock
to be running between data transfers, the clock must be
operating in order to write to EEPROM memory, even
though the data being saved may already be resident in
the DAC control register.
No clock is necessary upon system power-up. The
CAT524’s internal power-on reset circuitry loads data
from EEPROM to the DACs without using the external
clock.
As data transfers are edge triggered clean clock transi-
tions are necessary to avoid falsely clocking data into the
control registers. Standard CMOS and TTL logic fami-
lies work well in this regard and it is recommended that
any mechanical switches used for breadboarding or
device evaluation purposes be debounced by a flip-flop
or other suitable debouncing circuit.
DAC addressing is as follows:
DAC OUTPUT
A0
A1
VOUT1
0
0
VOUT2
1
0
VOUT3
0
1
VOUT4
1
1


Similar Part No. - CAT524JITE13

ManufacturerPart #DatasheetDescription
logo
Catalyst Semiconductor
CAT524JI-TE10 CATALYST-CAT524JI-TE10 Datasheet
105Kb / 13P
   Configured Digitally Programmable Potentiometer
More results

Similar Description - CAT524JITE13

ManufacturerPart #DatasheetDescription
logo
Catalyst Semiconductor
CAT522_0710 CATALYST-CAT522_0710 Datasheet
237Kb / 15P
   Configured Digitally Programmable Potentiometer (DPP??: Programmable Voltage Applications
CAT522 CATALYST-CAT522_07 Datasheet
236Kb / 15P
   Configured Digitally Programmable Potentiometer (DPP??: Programmable Voltage Applications
CAT523 CATALYST-CAT523 Datasheet
70Kb / 10P
   Configured Digitally Programmable Potentiometer (DPP): Programmable Voltage Applications
logo
ON Semiconductor
CAT521 ONSEMI-CAT521 Datasheet
213Kb / 13P
   Configured Digitally Programmable Potentiometer (DPP??: Programmable Voltage Applications
Doc. No. MD-2003 Rev. I
logo
Catalyst Semiconductor
CAT521 CATALYST-CAT521_07 Datasheet
207Kb / 13P
   Configured Digitally Programmable Potentiometer (DPP??: Programmable Voltage Applications
CAT525 CATALYST-CAT525 Datasheet
82Kb / 12P
   Configured Digitally Programmable Potentiometer (DPP??: Programmable Voltage Applications
CAT525 CATALYST-CAT525_07 Datasheet
254Kb / 16P
   Configured Digitally Programmable Potentiometer (DPP??: Programmable Voltage Applications
logo
ON Semiconductor
CAT522 ONSEMI-CAT522 Datasheet
236Kb / 15P
   Configured Digitally Programmable Potentiometer (DPP??: Programmable Voltage Applications
Doc. No. MD-2004 Rev. I
logo
Catalyst Semiconductor
CAT521 CATALYST-CAT521_04 Datasheet
73Kb / 10P
   Configured Digitally Programmable Potentiometer
CAT524 CATALYST-CAT524_04 Datasheet
105Kb / 13P
   Configured Digitally Programmable Potentiometer
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12


Datasheet Download

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEET.NET
Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com