OUTPUT SPECIFICATIONS

RR7-S05/D05

5 Watt 4:1 regulated

single & dual output

1) Typical value at nominal input voltage and full load.

2) Tested by nominal Vin and constant resistor load.

3) Measured input reflected ripple current with a simulated

source inductance of 12uH.

4) Exceeding the absolute ratings of the unit could cause

damage. It is not allowed for continuous operating.

5) It´s recommended to add C1 (68 F), C2 (33 F), L (12 H) in

input end to achieve EN55022 conducted Class A.

The models listed are just for standard type. If you need a special

specification product, please contact our service.

Phone: +49 69 984047-0, mail to: info@rsg-electronic.de or use the forms

on www.rsg-electronic.de („Kontakt“).

■

DIP24, wide 4:1 input range

■

Full SMD technology

■

1500 VDC isolation up to 3500 VDC isolation

■

Continuous short circuit protection

■

Efficiency up to 82%

■

-40°C~85°C operation temperature range

■

Optional Plastic case

■

EMI complies with EN55022 Class A

Voltage accuracy

± 1%

Line regulation

± 0.5%

Load regulation

± 0.5%

(Output 3.3V / ±3.3V Model)

± 1.5%

60 mV pk-pk

Short circuit protection

Indefinite (automatic recovery)

Temperature coefficient

± 0.02%/°C

See table

Voltage range

See table

Max. input current

See table

No-load input current

See table

Input filter

PI Type

35 mA pk-pk

INPUT SPECIFICATIONS

Efficiency (typ.)

See table

Metal case / input & output

1000 VDC

I/O isolation capacitance

500 pF typ.

I/O isolation resistance

1000 M Ohm

Switching frequency

typ. 266 kHz

Humidity

95% rel. H

> 1.121 Mhrs.

IEC 60950-1: 2001

GENERAL SPECIFICATIONS

Case material

Nickel-coated copper

Non-conductive black plastic

(UL94V-0 rated)

Base material

Non-conductive black plastic

(UL94V-0 rated)

Pin material

Ø 0.5 mm brass solder-coated

Potting material

Epoxy (UL94V-0 rated)

Weight

Metal 17.0 g, Plastic 13.5 g

Dimensions

1.25“ x 0.8“ x 0.4“

PHYSICAL SPECIFICATIONS

-40°C~ 85°C

Maximum case temperature

100°C

Storage temperature

-40°C~125°C

Cooling

Nature convection

ENVIRONMENT SPECIFICATIONS

NOTE

These are stress ratings. Exposure of devices to any of these

conditions may adversely affect long-term reliability.

Input voltage (100 mS)

24 modes

-0.7 ~ 40 VDC

48 modes

-0.7 ~ 80 VDC

Lead soldering temperature

260°C

(1.5 mm from case 10 sec.)

All specifications typical at Ta = 25°C, nominal input voltage and full load

unless otherwise specified.

The information and specifications contained in this data sheet are believed

to be correct at time of publication. However, we accept no responsibility

for consequences arising from printing errors or inaccuracies.

Subject to change without notice.

Page: 1/3

Last update: 18.02.10

RR-series, DIL 24 package, pic. similar

EMC SPECIFICATIONS

Radiated Emissions

EN55022

Class A

EN55022

Class A

ESD

IEC61000-4-2

Perf. crit. B

RS

IEC61000-4-3

Perf. crit. A

EFT

IEC61000-4-4

Perf. crit. B

CS

IEC61000-4-6

Perf. crit. A

PFMF

IEC61000-4-8

Perf. crit. A