Electronic Components Datasheet Search |
|
WRB1205LT-3WR2 Datasheet(PDF) 6 Page - MORNSUN Science& Technology Ltd. |
|
WRB1205LT-3WR2 Datasheet(HTML) 6 Page - MORNSUN Science& Technology Ltd. |
6 / 6 page The copyright and authority for the interpretation of the products are reserved by MORNSUN WRB_LT-3WR2 2013.03.12-A/1 Page 6 of 6 DESIGN CONSIDERATIONS 1) Requirement on output load To ensure this module can operate efficiently and reliably, during operation, the minimum output load could not be less than 5% of the full load, otherwise ripple maybe increase dramatically. If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load, suppose to use the resistance of 5% rated power,or use our company ’s products with a lower rated output power. 2) Recommended Circuit All the WRB_LT-3WR2 series have been tested according to the following recommended test circuit before leaving the factory(See Figure 6). If you want to further decrease the input/output ripple, you can increase a capacitance-values properly or choose capacitors with low ESR. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. Provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor must be less than the Max. Capacitive Load. General: Cin: 12V 100 μF 24V&48V 10 μF~47μF Cout: 10 μF/100mA DC DC Vin GND +Vo 0V Cin Co ut (Figure 6) 3) Input Current When it is used in unregulated power supply, be sure that the fluctuating range of the power supply and the rippled voltage do not exceed the module standard. Input current of power supply should afford the flash startup current of this kind of DC/DC module (Figure 7). General:Vin:12V Ip =640mA Vin:24V Ip =320mA Vin:48V Ip =160mA Input Voltage (V) Input Voltage Range Ip (Figure 7) 4) It is not recommended to increase the output power capability by connecting two or more converters in parallel. The product is not hot-swappable Note: 1. Min. load shouldn't be less than 5%, otherwise ripple maybe increased dramatically. If the product operates under min. load, it may not be guaranteed to meet all specifications listed. Operation under minimum load will not damage the converter. 2. Max. Capacitive Load is tested at input voltage range and full load. 3. All specifications measured at Ta=25 °C, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 4. In this datasheet, all test methods are based on our corporate standards. 5. All characteristics are for listed models,and non-standard models may perform differently.Please contact our technical support for more details. 6. Please contact our technical support for any specific requirement. 7. Specifications of this product are subject to changes without prior notice. MORNSUN Science & Technology Co.,Ltd. Address: No. 5, Kehui St. 1, Kehui development center, Science Ave., Guangzhou Science City, Luogang district, Guangzhou,P.R.China. Tel: 86-20-38601850 Fax:86-20-38601272 E-mail: info@mornsun.cn Http://www.mornsun-power.com |
Similar Part No. - WRB1205LT-3WR2 |
|
Similar Description - WRB1205LT-3WR2 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |