Electronic Components Datasheet Search |
|
TRPC03EL1C000E1G Datasheet(PDF) 4 Page - OPLINK Communications Inc. |
|
TRPC03EL1C000E1G Datasheet(HTML) 4 Page - OPLINK Communications Inc. |
4 / 5 page Oplink Communications, I nc. S0115,Rev.02 2010-12-23 Example ofSFP host board schematic TR PC0 3-E 1G Single Mode A pplication N otes Electrical Interface: All signal interfaces are compliant w ith the SFP MSA specification. The high speed D ATA interface is differential AC-coupled internally w ith 1 F and can be directly connected to a 3.3V SERD ES IC. All low speed control and sense output signals are open collector TTL compatible and should be pulled up w ith a 4.7 - 10k resistor on the host board. Loss of Signal (LOS): The Loss of Signal circuit monitors the level of the incoming optical signal and generates a logic H IG H w hen an insufficient photocurrent is produced. TX Fault: The output indicates LOW w hen the transmitter is operating normally,and H IG H w ith a laser fault including laser end-of-life. TX Fault is an open collector/drain output and should be pulled up w ith a 4.7 - 10k resistor on the host board. TX Fault is non-latching (automatically deasserts w hen fault goes aw ay). TX Disable: W hen the TX D isable pin is at logic H IG H ,the transmitter optical output is disabled (less than -45dBm). Serial Identification and Monitoring:The module definition of SFP is indicated by the three module definition pins, MOD _D EF(0),MOD _D EF(1)and MOD _D EF(2). U pon pow er up, MOD _D EF(1:2)appear as N C (no connection),and MOD _D EF(0) is TTL LOW . W hen the host system detects this condition, it activates the serial protocol (standard tw o-w ire I2C serial interface) and generates the serial clock signal (SCL). The positive edge clocks data into the EEPROM segments of the SFP that are not w rite protected,and the negative edge clocks data from the SFP. The serial data signal (SD A) is for serial data transfer. The host uses SD A in conjunction w ith SCL to mark the start and end of serial protocol activation. The supported monitoring functions are temperature,voltage,bias current,transmitter pow er,average receiver signal,all alarms and w arnings,and softw are monitoring of TX Fault/LOS. The device is internally calibrated. The data transfer protocol and the details of the mandatory and vendor specific data structures are defined in the SFP MSA, and SFF-8472,Rev. 9.4. Pow er Supply and G rounding:The pow er supply line should be w ell-filtered. All 0.1 F pow er supply bypass capacitors should be as close to the transceiver module as possible. 4 R:4.7 to 10k CAP Values in µF 18 19 3 TX DATA IN+ 15 1 H coi lorf erri t ebead m (<0. 2 seri esresi st ance) W 0. 1 TX DATA IN- TX Di sabl e 16 0. 1 + 10 50 l i ne W 1,9, 10, 11, 14, 17, 20 0. 1 + 10 to 50 load W Vcc 3. 3V RX DATA OUT+ 13 12 RX DATA OUT- 5 4 6 MOD_DEF(0) MOD_DEF(1) MOD_DEF(2) LOS to 50 load W 8 R 2 TX Faul t R R R Vcc 3. 3V 50 l i ne W 50 l i ne W 50 l i ne W R TRPC03-E1G |
Similar Part No. - TRPC03EL1C000E1G |
|
Similar Description - TRPC03EL1C000E1G |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |