Electronic Components Datasheet Search |
|
HI-8683PJI Datasheet(PDF) 4 Page - Holt Integrated Circuits |
|
HI-8683PJI Datasheet(HTML) 4 Page - Holt Integrated Circuits |
4 / 10 page HI-8683, HI-8684 HOLT INTEGRATED CIRCUITS 4 ERROR CHECKING READING RECEIVE BUFFER Oncea word gap is detected, the data word in the input reg- ister is transferred to the receive buffer and checked for er- rors. When parity detection is enabled (PARITY ENB high), the received word is checked for odd parity. If there isa parity error, the 32nd bit of the received data word is set high. If parity checking is disabled (PARITY ENB low) the 32nd bit of the data word is always the 32nd ARINC bit received. The ERROR flag output is set high upon receipt ofa word gap and the number of bits received since the previous word gap is less than or greater than 32. The ERROR flag is reset low when the next valid ARINC word is written into the receive buffer or when is pulsed low. When the data word is transferred to the receive buffer, the DATA RDY pin goes high. The data word can then be read in four 8-bit bytes by pulsing the input low as indi- cated in Figure 5. The first read cycle resets DATA RDY low and increments an internal counter to the next 8-bit byte. The counter continues to increment on each read cy- cle until all four bytes are read. The relationship between each bit of an ARINC word received and each bit of the four 8-bit data bus bytes is specified in Figure 2. Whena new ARINC word is received it always overwrites the receive buffer. If the first byte of the previous word has not been read, then previous data is lost and the receive buffer will contain the new ARINC word. However, if the DATA RDY pin goes high between the reading of the first and fourth bytes, the previous read bytes are no longer valid because the unread bytes have been overwritten by the new ARINC word. Also, the next read will be of the first byte of the new ARINC word since the internal byte counter is always reset to the first byte when new data is trans- ferred to the receive buffer. RESET READ FUNCTIONAL DESCRIPTION (cont.) TRUTH TABLE 1. RINA RINB TESTA TESTB RXA RXB -1.50 to +1.50V -1.50V to +1.50V 0 00 0 -3.25V to -6.50V +3.25V to +6.50V 0 00 1 +3.25V to +6.50V -3.25V to -6.50V 0 01 0 X X 0 10 1 X X 1 01 0 X X 1 10 0 X= don't care Read Byte Data Bus Bits ARINC Bits 1st Byte 1 D0- D7 ARINC1- ARINC 8 2nd Byte 2 D0- D7 ARINC9- ARINC 16 3rd Byte 3 D0- D7 ARINC 17- ARINC 24 4th Byte 4 D0- D7 ARINC 25- ARINC 32 FIGURE 2. ORDER OF RECEIVED DATA RESET TEST MODE (HI-8684 only) A low on the input setsa flip-flop which initializes the internal logic. When goes high, the internal logic remains in the initialized state until the first word gap is detected preventing reception ofa partial word. The built-in differential line receiver on the HI-8684 can be disabled allowing the data and clock detection circuitry to be driven directly with digital signals. The logical OR func- tion of the TESTA and TESTB is defined in Truth Table 1. The two inputs can be used for testing the receiver logic and for inputting ARINC 429 type data derived from another source/ protocol. See Figure4 for typical test input timing. The device should always be initialized with imme- diately after entering the test mode to cleara partial word that may have been received since the last word gap. Oth- erwise, an ERROR condition may occur and the first 32 bits of data on the test inputs may not be properly re- ceived. Also, when entering the test mode, both TESTA and TESTB should be set high and held in that state for at least one word gap period (17 gap clocks) after goes high. When exiting the test mode, both test inputs should be held low and the device initialized with RESET RESET RESET RESET RESET. |
Similar Part No. - HI-8683PJI |
|
Similar Description - HI-8683PJI |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |