Electronic Components Datasheet Search |
|
IDT72V3670L10PF Datasheet(PDF) 10 Page - Integrated Device Technology |
|
IDT72V3670L10PF Datasheet(HTML) 10 Page - Integrated Device Technology |
10 / 36 page 10 COMMERCIAL AND INDUSTRIAL TEMPERATURERANGES IDT72V3640/50/60/70/80/90/110 3.3V HIGH DENSITY SUPERSYNC IITM 36-BIT FIFO 1,024 x 36, 2,048 x 36, 4,096 x 36, 8,192 x 36, 16,384 x 36, 32,768 x 36, 65,536 x 36, 131,072 x 36 PROGRAMMING FLAG OFFSETS FullandEmptyFlagoffsetvaluesareuserprogrammable.TheIDT72V3640/ 72V3650/72V3660/72V3670/72V3680/72V3690/72V36100/72V36110have internalregistersfortheseoffsets.Thereareeightdefaultoffsetvaluesselectable during Master Reset. These offset values are shown in Table 2. Offset values can also be programmed into the FIFO in one of two ways; serial or parallel loadingmethod.Theselectionoftheloadingmethodisdoneusingthe LD(Load) pin. During Master Reset, the state of the LD input determines whether serial or parallel flag offset programming is enabled. A HIGH on LD during Master Resetselectsserialloadingofoffsetvalues. ALOWon LDduringMasterReset selects parallel loading of offset values. In addition to loading offset values into the FIFO, it is also possible to read the current offset values. Offset values can be read via the parallel output port Q0-Qn, regardless of the programming mode selected (serial or parallel). It is not possible to read the offset values in serial fashion. Figure 3, Programmable Flag Offset Programming Sequence, summaries thecontrolpinsandsequenceforbothserialandparallelprogrammingmodes. For a more detailed description, see discussion that follows. Theoffsetregistersmaybeprogrammed(andreprogrammed)anytimeafter Master Reset, regardless of whether serial or parallel programming has been selected. Valid programming ranges are from 0 to D-1. SYNCHRONOUS vs ASYNCHRONOUS PROGRAMMABLE FLAG TIM- ING SELECTION The IDT72V3640/72V3650/72V3660/72V3670/72V3680/72V3690/ 72V36100/72V36110 can be configured during the Master Reset cycle with either synchronous or asynchronous timing for PAF andPAE flags by use of the PFM pin. If synchronous PAF/PAE configuration is selected (PFM, HIGH during MRS), the PAF is asserted and updated on the rising edge of WCLK only and not RCLK. Similarly, PAEisassertedandupdatedontherisingedgeofRCLK only and not WCLK. For detail timing diagrams, see Figure 17 for synchronous PAF timing and Figure 18 for synchronous PAE timing. If asynchronous PAF/PAE configuration is selected (PFM, LOW during MRS),thePAFisassertedLOWontheLOW-to-HIGHtransitionofWCLKand PAFisresettoHIGHontheLOW-to-HIGHtransitionofRCLK. Similarly, PAE isassertedLOWontheLOW-to-HIGHtransitionofRCLK. PAEisresettoHIGH ontheLOW-to-HIGHtransitionofWCLK.Fordetailtimingdiagrams,seeFigure 19 for asynchronous PAF timingandFigure20forasynchronous PAEtiming. IDT72V3640, 72V3650 LD FSEL1 FSEL0 Offsets n,m LH L 511 L L H 255 L L L 127 LH H 63 HL L 31 HH L 15 HL H 7 HH H 3 LD FSEL1 FSEL0 Program Mode H X X Serial(3) L X X Parallel(4) IDT72V3660, 72V3670, 72V3680, 72V3690 LD FSEL1 FSEL0 Offsets n,m H L L 1,023 LH L 511 L L H 255 L L L 127 LH H 63 HH L 31 HL H 15 HH H 7 LD FSEL1 FSEL0 Program Mode H X X Serial(3) L X X Parallel(4) IDT72V36100, 72V36110 LD FSEL1 FSEL0 Offsets n,m L H L 16,383 L L H 8,191 L H H 4,095 H H L 2,047 H L L 1,023 HL H 511 HHH 255 LLL 127 LD FSEL1 FSEL0 Program Mode H X X Serial(3) L X X Parallel(4) TABLE 2 DEFAULT PROGRAMMABLE FLAG OFFSETS NOTES: 1. n = empty offset for PAE. 2. m = full offset for PAF. 3. As well as selecting serial programming mode, one of the default values will also be loaded depending on the state of FSEL0 & FSEL1. 4. As well as selecting parallel programming mode, one of the default values will also be loaded depending on the state of FSEL0 & FSEL1. |
Similar Part No. - IDT72V3670L10PF |
|
Similar Description - IDT72V3670L10PF |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |