ADE7762

Rev. 0 | Page 7 of 28

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

LED_B

28

LED_C

27

F1

26

F2

25

S1

24

S0

23

CLKOUT

22

CLKIN

21

SCF

20

ABS

19

VAP

18

VBP

17

VCP

16

VN

15

ADE7762

TOP VIEW

(Not to Scale)

Figure 4. Pin Configuration

Table 4. Pin Function Descriptions

Pin No.

Mnemonic

Description

1

LED_CTRL

LED Control Output. The LED_CTRL signal multiplexes the indication of phase drop, phase sequence

error, and per phase reverse power on the LED_A, LED_B, and LED_C pins.

2

LED_A

Phase A Phase Monitor Output. LEDs are connected to this pin to indicate phase drop or reverse power

on Phase A (see the Phase Monitor section).

3

CF

Calibration Frequency Logic Output. The CF logic output gives instantaneous active power information.

This output is intended to be used for calibration purposes.

4

DGND

This provides the ground reference for the digital circuitry in the ADE7762, that is, multipliers, filters,

and digital-to-frequency converters. Because the digital return currents in the ADE7762 are small, it is

acceptable to connect this pin to the analog ground plane of the whole system.

5

Power Supply. This pin provides the supply voltage for the digital circuitry in the ADE7762. The supply

voltage should be maintained at 5 V ± 5% for a specified operation. This pin should be decoupled to

DGND with a 10 μF capacitor in parallel with a 100 nF ceramic capacitor.

6

REVP

This logic output goes logic high when negative power is detected on the sum of the three phase

powers. This output is not latched and resets when positive power is once again detected (see the

Negative Total Power Detection section).

7, 8;

9, 10;

11, 12

IAP, IAN;

IBP, IBN;

ICP, ICN

Analog Inputs for Current Channels. These channels are intended for use with current transducers and

are referenced in this document as current channels. These inputs are fully differential voltage inputs

with maximum differential input signal levels of ±0.5 V (see the Analog Inputs section). Both inputs

have internal ESD protection circuitry; in addition, an overvoltage of ±6 V can be sustained on these

inputs without risk of permanent damage.

13

AGND

This pin provides the ground reference for the analog circuitry in the ADE7762 (ADCs and reference).

This pin should be tied to the analog ground plane or the quietest ground reference in the system. This

quiet ground reference should be used for all analog circuitry, such as antialiasing filters and current

and voltage transducers. To keep ground noise around the ADE7762 to a minimum, the quiet ground

plane should connect to the digital ground plane at only one point. It is acceptable to place the entire

device on the analog ground plane.

14

This pin provides access to the on-chip voltage reference. The on-chip reference has a nominal value of

2.4 V ± 8% and a typical temperature coefficient of 25 ppm/°C. An external reference source can also be

connected at this pin. In either case, this pin should be decoupled to AGND with a 1 μF ceramic

capacitor.

15, 16, 17,

18

VN, VCP, VBP, VAP

Analog Inputs for the Voltage Channels. These channels are intended for use with voltage transducers

and are referenced in this document as voltage channels. These inputs are single-ended voltage inputs

with a maximum signal level of ±0.5 V with respect to VN for a specified operation. All inputs have

internal ESD protection circuitry; in addition, an overvoltage of ±6 V can be sustained on these inputs

without risk of permanent damage.

19

ABS

This logic input is used to select the method by which the three active energies from each phase are

summed. It selects between the arithmetical sum of the three energies (ABS logic high) or the sum of

the absolute values (ABS logic low). See the Mode Selection of the Sum of the Three Active Energies

section.

20

SCF

Select Calibration Frequency. This logic input is used to select the frequency on the calibration output

CF. Table 7 shows how the calibration frequencies are selected.