Electronic Components Datasheet Search |
|
UPD45128841G5-A10-9JF Datasheet(PDF) 10 Page - NEC |
|
UPD45128841G5-A10-9JF Datasheet(HTML) 10 Page - NEC |
10 / 92 page Data Sheet M12650EJBV0DS00 10 µµµµPD45128441, 45128841, 45128163 1. Input / Output Pin Function Pin name Input / Output Function CLK Input CLK is the master clock input. Other inputs signals are referenced to the CLK rising edge. CKE Input CKE determine validity of the next CLK (clock). If CKE is high, the next CLK rising edge is valid; otherwise it is invalid. If the CLK rising edge is invalid, the internal clock is not issued and the µPD45128xxx suspends operation. When the µPD45128xxx is not in burst mode and CKE is negated, the device enters power down mode. During power down mode, CKE must remain low. /CS Input /CS low starts the command input cycle. When /CS is high, commands are ignored but operations continue. /RAS, /CAS, /WE Input /RAS, /CAS and /WE have the same symbols on conventional DRAM but different functions. For details, refer to the command table. A0 - A11 Input Row Address is determined by A0 - A11 at the CLK (clock) rising edge in the active command cycle. It does not depend on the bit organization. Column Address is determined by A0 - A9, A11 at the CLK rising edge in the read or write command cycle. It depends on the bit organization: A0 - A9, A11 for ×4 device, A0 - A9 for ×8 device, A0 - A8 for ×16 device. A10 defines the precharge mode. When A10 is high in the precharge command cycle, all banks are precharged; when A10 is low, only the bank selected by BA0(A13) and BA1(A12) is precharged. When A10 is high in read or write command cycle, the precharge starts automatically after the burst access. BA0, BA1 Input BA0(A13) and BA1(A12) are the bank select signal. In command cycle, BA0(A13) and BA1(A12) low select bank A, BA0(A13) high and BA1(A12) low select bank B, BA0(A13) low and BA1(A12) high select bank C and then BA0(A13) and BA1(A12) high select bank D. DQM, UDQM, LDQM Input DQM controls I/O buffers. In ×16 products, UDQM and LDQM control upper byte and lower byte I/O buffers, respectively. In read mode, DQM controls the output buffers like a conventional /OE pin. DQM high and DQM low turn the output buffers off and on, respectively. The DQM latency for the read is two clocks. In write mode, DQM controls the word mask. Input data is written to the memory cell if DQM is low but not if DQM is high. The DQM latency for the write is zero. DQ0 - DQ15 Input / Output DQ pins have the same function as I/O pins on a conventional DRAM. VCC, VSS, VCCQ, VSSQ (Power supply) VCC and VSS are power supply pins for internal circuits. VCCQ and VSSQ are power supply pins for the output buffers. |
Similar Part No. - UPD45128841G5-A10-9JF |
|
Similar Description - UPD45128841G5-A10-9JF |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |