Electronic Components Datasheet Search |
|
LT1371HVCR Datasheet(PDF) 7 Page - Linear Technology |
|
LT1371HVCR Datasheet(HTML) 7 Page - Linear Technology |
7 / 16 page 7 LT1371 APPLICATIO S I FOR ATIO Unique error amplifier circuitry allows the LT1371 to directly regulate negative output voltages. The negative feedback amplifier’s 100k source resistor is brought out for negative output voltage sensing. The NFB pin regulates at – 2.49V while the amplifier output internally drives the FB pin to 1.245V. This architecture, which uses the same main error amplifier, prevents duplicating functions and maintains ease of use. Consult LTC Marketing for units that can regulate down to – 1.25V. The error signal developed at the amplifier output is brought out externally. This pin (VC) has three different functions. It is used for frequency compensation, current limit adjustment and soft starting. During normal regula- tor operation this pin sits at a voltage between 1V (low output current) and 1.9V (high output current). The error amplifier is a current output (gm) type, so this voltage can be externally clamped for lowering current limit. Like- wise, a capacitor coupled external clamp will provide soft start. Switch duty cycle goes to zero if the VC pin is pulled below the control pin threshold, placing the LT1371 in an idle mode. Positive Output Voltage Setting The LT1371 develops a 1.245V reference (VREF) from the FB pin to ground. Output voltage is set by connecting the FB pin to an output resistor divider (Figure 1). The FB pin bias current represents a small error and can usually be ignored for values of R2 up to 7k. The suggested value for R2 is 6.19k. The NFB pin is normally left open for positive output applications. Positive fixed voltage versions are available (consult LTC Marketing). Negative Output Voltage Setting The LT1371 develops a – 2.49V reference (VNFR) from the NFB pin to ground. Output voltage is set by connecting the NFB pin to an output resistor divider (Figure 2). The –30 µA NFB pin bias current (INFB) can cause output voltage errors and should not be ignored. This has been accounted for in the formula in Figure 2. The suggested value for R2 is 2.49k. The FB pin is normally left open for negative output applications. See Dual Polarity Output Voltage Sensing for limitations on FB pin loading when using the NFB pin. Dual Polarity Output Voltage Sensing Certain applications benefit from sensing both positive and negative output voltages. One example is the “Dual Output Flyback Converter with Overvoltage Protection” circuit shown in the Typical Applications section. Each output voltage resistor divider is individually set as de- scribed above. When both the FB and NFB pins are used, R1 VOUT = VREF 1 + R2 FB PIN VREF VOUT ()R1 R2 R1 = R2 – 1 () VOUT 1.245 LT1371 • F01 the LT1371 acts to prevent either output from going beyond its set output voltage. For example, in this applica- tion if the positive output were more heavily loaded than the negative, the negative output would be greater and would regulate at the desired set-point voltage. The posi- tive output would sag slightly below its set-point voltage. This technique prevents either output from going unregu- lated high at no load. Please note that the load on the FB pin should not exceed 250 µA when the NFB pin is used. This situation occurs when the resistor dividers are used at both FB and NFB. True load on FB is not the full divider current unless the positive output is shorted to ground. See Dual Output Flyback Converter application. APPLICATIO S I FOR ATIO Figure 1. Positive Output Resistor Divider Figure 2. Negative Output Resistor Divider R1 –VOUT = VNFB + INFB (R1) 1 + R2 LT1371 • F02 NFB PIN VNFR INFB –VOUT ()R1 R2 R1 = + 30 • 10 –6 VOUT– 2.49 ( ) ( ) 2.49 R2 |
Similar Part No. - LT1371HVCR |
|
Similar Description - LT1371HVCR |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |