Electronic Components Datasheet Search |
|
MAX499 Datasheet(PDF) 3 Page - Maxim Integrated Products |
|
MAX499 Datasheet(HTML) 3 Page - Maxim Integrated Products |
3 / 16 page TIMING CHARACTERISTICS (VCC = +5V, VEE = -5V, VIN_ _ = 0V, RL = 150Ω, LE = EN = CS = 0V, TA = 0°C to +70°C. Typical values are at TA = +25°C, unless otherwise noted.) Quad/Triple, SPDT, RGB Switches with 250MHz Video Buffer Amplifiers _______________________________________________________________________________________ 3 f = 10MHz (Note 3) f = 10MHz (Note 2) f = 3.58MHz (Note 5), RL = 150Ω fC = 3MHz f = 10MHz f = 100kHz f = 3.58MHz (Note 5), RL = 150Ω f = 100kHz EN = 1, f = 10MHz (Note 4) CONDITIONS degrees 0.06 Diff Phase Differential Phase % 0.03 Diff Gain Differential Gain dB 81 Off-Isolation dB 62 All-Hostile Crosstalk dB 90 Adjacent-Channel Crosstalk dBc -66 SFDR Spurious-Free Dynamic Range dB -50 THD Total Harmonic Distortion nV/ √Hz 7.8 Input Voltage Noise Density pA/ √Hz 2.6 Input Current Noise Density UNITS MIN TYP MAX SYMBOL PARAMETER AC ELECTRICAL CHARACTERISTICS (VCC = +5V, VEE = -5V, VIN__ = 0V, RL = 100Ω, LE = EN = CS = 0V, TA = +25°C, unless otherwise noted.) 0.1%, VOUT = 4V step ns 12 ts Settling Time VOUT = 4V step V/µs 1250 SR Slew Rate VOUT = ±2V MHz 135 FPBW Full-Power, -3dB Bandwidth VIN ≤ 100mVp-p MHz 70 ±0.1dB Gain Flatness VIN ≤ 100mVp-p MHz 250 BW-3dB Small-Signal, -3dB Bandwidth Note 2: Test-channel input grounded through a 50 Ω resistor. Adjacent channel driven to a 2Vp-p output with a 10MHz sine wave (Figure 9). Note 3: Same as Note 2, except all channels but the test channel are driven to a 2Vp-p output with a 10MHz sine wave (Figure 9). Note 4: Test-channel input connected to a 2Vp-p sine wave at 10MHz. The test channel’s output is measured with the outputs disabled (Figure 9). Note 5: Input test signal is a 3.58MHz sine wave of 40IRE amplitude, superimposed on a 0IRE to 100IRE linear ramp (Figure 10). Note 6: Guaranteed by design. Note 7: VINA = +1V, VINB = -1V, delay from CS to 10% of VOUT. Note 8: VINA = +1V, VINB = -1V, delay from CS to 10% of VOUT. Note 9: Delay from EN to 90% of VOUT. Note 10: Delay from EN to 10% of VOUT. Positive (Note 8) (Note 7) VINA = VINB = 0V (Note 6) LE = high (Note 6) LE = high (Note 6) CONDITIONS 70 ns 3 tSW Channel-Switching Time ns 20 tPD Channel-Switching Propagation Delay ns 15 tCS CS Pulse Width ns 4 tH A0/ EN to CS Hold Time ns 8 tSU A0/ EN to CS Setup Time mV UNITS MIN TYP MAX SYMBOL PARAMETER Channel-Switching Transient (Note 9) 16 ns tOFF Amplifier-Disable Time (Note 10) 24 ns tON Amplifier-Enable Time Negative 50 Negative Positive 150 VINA = VINB = 0V 10 mV Enable/Disable Switching Transient |
Similar Part No. - MAX499 |
|
Similar Description - MAX499 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |