Electronic Components Datasheet Search |
|
MAX6160ESA Datasheet(PDF) 7 Page - Maxim Integrated Products |
|
MAX6160ESA Datasheet(HTML) 7 Page - Maxim Integrated Products |
7 / 8 page _______________________________________________________________________________________ 7 _____________Applications Information Setting the MAX6160 Output Voltage Set the output voltage on the MAX6160 by connecting a resistor divider between OUT, ADJ, and GND (Figure 1). Choose R1 according to the following equa- tion: R1 = (1.06 x 105) (VOUT / VADJ)(k Ω) where VTH = 1.23V. The scaling factor (1.06 x 105) compensates for the MAX6160's change in ADJ input current over temperature. When R1 is chosen correctly, the change in voltage across R1 caused by the ADJ input current is properly cancelled. Choose R1 to within ±5% of this calculated value (nearest standard value plus specified resistor tolerance) to optimize the output voltage temperature coefficient. Using R1 = 215k Ω: which is also the nearest 0.1% resistor value. Choose R2 according to the following equation: R2 = R1 / (VOUT / VADJ - 1) For example, a 2.5V output requires R1 = (1.06 x 105) (2.5V / 1.23V) ≈ 215Ω, which is the nearest standard- value 0.1% resistor. Input Bypassing For the best line-transient performance, decouple the input with a 0.1µF ceramic capacitor, as shown in the Typical Operating Circuit. Locate the capacitor as close to the device pin as possible. Where transient performance is less important, no capacitor is necessary. Output Bypassing The MAX6125/MAX6141/MAX6145/MAX6150/MAX6160 do not require an output capacitor. They are stable for capacitive loads from 0nF to 10nF. If your application requires an output charge reservoir (e.g., to decouple the reference from a DAC’s input), then make sure that the total output capacitive load does not exceed 10nF for optimum settling-time performance. SOT23, Low-Cost, Low-Dropout, 3-Terminal Voltage References ______________________________________________________________Pin Description Adjustable output voltage feedback input. Connect a resistor divider between OUT, ADJ, and GND (Figure 1). ADJ 5** Input Voltage IN 8 Ground GND 4 No Connection. Not internally connected. N.C. 2, 3, 5*, 6, 7 Reference Output OUT 1 FUNCTION NAME SO — 1 3 — 2 SOT23-3 2 3 1 — 4 SOT143 * Except MAX6160. ** MAX6160 only. MAX6160 OUT ADJ GND IN R1 = 1.06 x 105 (––––) ( kΩ) VOUT VADJ R2 = –—–––– VOUT VADJ (–––– - 1) R1 VADJ = 1.23V VOUT VIN R1 R2 Figure 1. MAX6160 Adjustable Output Circuit PIN R2 = 215k 2.5V 1.23V - 1 208k Ω ≈Ω, |
Similar Part No. - MAX6160ESA |
|
Similar Description - MAX6160ESA |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |