www.micropowerdirect.com

The diagram above illustrates a typical connection of the MPM-10SV series.

The input components are required to meet the more stringent EFT/Surge levels

of EN 61000-4 (see notes for EMC Characteristics table above). Some notes on

these components are:

1. It is recommended that an external fuse be used. The recommended fuse

size is a 2.0A/300 VAC slow blow.

2. An external MOV is recommended on the input to protect the unit in the event

of a surge. A recommended value is given in the table at right.

specified levels. Recommended values are given in the table on page 2.

4. TheTVS is added to protect circuits being powered from damage if the module

fails. A recommended value for each model is given in the table on page 2.

Notes:

1. To meet the requirements of EN 61000-

4-4 (±4 kV), external components are

needed. This can be done discretely (as

shown below), or with the addition of the

MACFM-02A. Contact the factory for more

information.

2. To meet the requirements of EN 61000-4-5

(±2 kV/ ±4 kV ), external components are

needed. This can be done discretely (as

shown below), or with the addition of the

MACFM-02A. Contact the factory for more

information.

5. Suggested component values are:

Component

MPM10SV-03

MPM10SV-05

MPM10SV-09

MPM10SV-12

MPM10SV-15

MPM10SV-24

Fuse

2.0A/300 VAC

2.0A/300 VAC

2.0A/300 VAC

2.0A/300 VAC

2.0A/300 VAC

2.0A/300 VAC

MOV

S14K350

S14K350

S14K350

S14K350

S14K350

S14K350

0.1 µF/310V

0.1 µF/310V

0.1 µF/310V

0.1 µF/310V

0.1 µF/310V

0.1 µF/310V

LDM

4.7 µH/2A

4.7 µH/2A

4.7 µH/2A

4.7 µH/2A

4.7 µH/2A

4.7 µH/2A

LCM

10 mH

10 mH

10 mH

10 mH

10 mH

10 mH

1,000 pF/400VAC 1,000 pF/400VAC 1,000 pF/400VAC 1,000 pF/400VAC 1,000 pF/400VAC 1,000 pF/400VAC

6. Input protection and filtering modules are available for a number of MPD AC/DC power supplies. For use with the MPM-10SV product series,

the MACFM-02A filter module is recommended. A typical connection diagram and board layout with this module is shown in the figures

below. For pricing or full technical information on the MACFM-02A (or any of our other modules) please contact the factory.

Parameter

Conditions

Criteria

Level

Radiated Emissions

EN 55022

Class B

Conducted Emissions

EN 55022

Class B

ESD

EN 61000-4-2

B

±8 kV Air

±6 kV Contact

RS

EN 61000-4-3

A

10V/m

EFT

EN 61000-4-4

B

±2 kV

See Note 1

B

±4 kV

Surge

EN 61000-4-5

B

±1 kV/±2 kV

See Note 2

B

±2 kV/±4 kV

CS

EN 61000-4-6

A

10V rms

PFM

EN 61000-4-8

A

10A/m

Voltage Dips, Short, Interruptions

EN 61000-4-11

B

0% - 70%

EMI Characteristics

1. The width of circuit traces should be a minimum of 3 mm.

2. The distance between traces should be a minimum of 6 mm.

3. The distance between a trace and ground should be a minimum of 6 mm.