100W Single Output Switching Power Supply

WWW.ASTRODYNETDI.COM

ASTRODYNE USA: 1-800-823-8082

ASTRODYNE PACIFIC: 886-2-26983458

INPUT SPECIFICATIONS

Input Voltage Range

88 ~ 132 VAC / 176~264 VAC auto switch

248~370 Volts(DC)

Frequency Range

47-63 Hz

Inrush Current, typ: (cold start)30Amps@115VAC / 60Amps@230VAC

Input Current, typ.

2.3Amps@115VAC

1.5Amps@230VAC

Leakage current

< 1mAmps /240VAC

Min Load

See Selection Chart

OUTPUT SPECIFICATIONS

Voltage and Current

See Selection Chart

Line Regulation

±0.5%

Load Regulation

±2.0%: 3.3~5Volts(DC)

±1.5%: .5~15Volts(DC)

±0.5%: 24~48Volts(DC)

Voltage Tolerance (Note2)

See Selection Chart

Ripple/Noise (Note 1)

See Selection Chart

Hold Up Time,typ @ FL

20mS/230VAC

20mS/115VAC

Setup, Rise Time @ FL

800ms, 50m/230VAC

1200mS, 50mS/115VAC

Over Voltage Protection

3.8 ~ 4.45Volt(DC): 3.3Volts(DC)

5.75 ~ 6.75Volt(DC): 5Volts(DC)

9.4 ~ 10.9Volt(DC): 7.5Volts(DC)

13.8 ~ 16.2Volt(DC): 12Volts(DC)

15.5 ~ 18.2Volt(DC): 13.5Volts(DC)

18 ~ 21Volt(DC): 15Volts(DC)

27.6~ 32.4Volt(DC): 24Volts(DC)

33.7 ~ 39.2Volt(DC): 5Volts(DC)

57.6~ 67.2Volt(DC): 48Volts(DC)

Hiccup mode, auto recover

Over Current Protection

105 ~ 140% (+24Volts: above 6.5Amps)

rated output power

Hiccup mode, auto recover

DC Volt Adjust

See Selection Chart

GENERAL SPECIFICATIONS

Safety

UL60950-1,

TUV EN60950-1 Approved

Insulation Resistance

≥ 100MΩ / 500Volts(DC)

EMI

Compliance to EN55022B (CISPR22B)

Harmonic Current

Compliance to EN61000-3-2,-3

Efficiency, typ.

69% (LPS-100-3.3)

77% (LPS-100-5/7.5)

79% (LPS-100-12/13.5)

80% (LPS-100-15/24)

81% (LPS-100-27/48)

Isolation

3000VAC Input - Output

1500VAC Input - Ground

500VAC Output - Ground

EMS

Compliance to EN61000-4-2,3,4,5,6,8,11

light Industry Level, Criteria A

Remote ON/OFF

RC+/RC-: 0~0.8Volts(DC)= power On

4~10Volts(DC)= power Off

ENVIRONMENTAL SPECIFICATIONS

Oper. Temperature

-10°C to +60°C (See Derate Curve)

Storage Temperature

-20°C to +85°C, 10~95% RH

Relative Humidity

20~90% RH non cond

Temperature Coefficient

±0.05% / °C (0-50°C)

MTBF

203.6KHrs min,MIL-HDBK-217F(25°C)

Vibration

10~500Hz, 2G10min./1cycle, period for

60min. each along X, Y, Z axes

PHYSICAL SPECIFICATIONS

Size

Millimeters

222 x 62 x 32

Inches

8.74” x 2.44 ” x 1.26 ”

Weight

15.87 oz (450g)

NOTE

1. Ripple & noise are measured at 20MHz of bandwidth by using a 12”

twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

2. Tolerance : includes set up tolerance, line regulation and load regula-

tion.

3. If the input range 85V-89V, the output load is changed from 0A-rated

load, There will be reduced 20V for 1second (LPS-100-24).

4. Mounting holes M1 and M2 should be grounded for EMI purposes.

All specifications are typical at nominal input, full load, and 25°C unless other-

wise noted