Electronic Components Datasheet Search |
|
LF06P2-W4F-840-P Datasheet(PDF) 3 Page - OSRAM GmbH |
|
LF06P2-W4F-840-P Datasheet(HTML) 3 Page - OSRAM GmbH |
3 / 4 page www.osram.com/flex Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. Subject to change without notice. Errors and omissions excepted. Version: 2016-07-12 LINEARlight POWER Flex® Protect G2.1 (2016) – LF06P2-P 3/4 In order to drive OSRAM LED-Modules safely, it is absolutely necessary to operate them with an electronically stabilized power supply protecting against short circuits, overload and overheating. To also ease the luminaire/installation approval, electronic control gear for LED or LED modules should carry the CE mark and be ENEC certified. In Europe the declarations of conformity must include the following standards: CE: EC 61347-2-13, EN 55015, IEC 61547 and IEC 61000-3-2 - ENEC: 61347-2-13 and IEC/EN 62384. Also check for the mark of an independent authorized certification institute. Please see the relevant brochure for more detailed information (see "Related and Further Information") OSRAM OPTOTRONIC® control gear complies to all relevant standards and guarantees safe operation. Assembly Information ► The smallest electrical unit (SEU) (150 mm- 6 LEDs) can be removed by cutting at the printed marks at the side. ► After cutting connect the module via CONNECTsystem IP67 LP. Insert module into connector and apply pressure on a hard surface until locked. ► The mounting of the single LED coupons is facilitated by means of the double-sided adhesive on the back surface of the module. Care must be taken to provide a clean and dry mounting surface, free of oils or silicone coatings as well as dirt particle. The mounting substrate must have sufficient structural integrity. Take care to completely remove the adhesive backing. Once the module is appropriately positioned, press on the module with about 20N/cm² (refer to application techniques of Tesa adhesive transfer tapes). To support adhesion at higher temperatures, use additional mounting brackets if temperature exceeds Tc = 40°C. ► The module has to be mounted on a metal heat sink! ► The minimum bending radius is 5 cm. ► When installing in environments with large variations in temperature (e.g. outdoor applications) and operating length of more than 2 m, the use of adequate mounting surfaces is necessary . Otherwise it is advisable to use an additional thicker adhesive tape to absorb the stress of any mismatch in expansion. ► If temperature exceeds Tc = 40°C, additional mounting brackets are needed. ► Pay attention to avoid highly corrosive atmospheres, e.g. permanent high humidity or Hydrogen Sulfide (H2S). With current LED technology, H2S is causing accelerated corrosion which will lead to shortened timelife or premature failure. Sources for H2S may be rubber, foamed rubber, soft-foam-tapes, sealings on rubber basis, natural sources (e.g. sulfur springs), etc. To avoid H2S from sulfur-vulcanized rubber it is necessary to switch to silicon based materials or rubber that is Peroxid-crosslinked. Indication may be found in the material datasheet of the rubber supplier. Complementary systems and accessories Accessories Type Product EAN Shipping units CONNECTsystem IP67 Endcap for module LF-ENDCAP IP67 LP 4052899902565 10 2pin Feeder LF-2PIN IP67 LP 4052899125711 5 2pin Jumper LF-2CONN IP67 LP 4052899125735 5 SLIMCONNECTsystem IP54 2pin Feeder LF-2PIN Flex IP SC 4008321841902 10 Jumper (board-to-board) (also add: 4008321841926) LF-CONN Flex SC 4008321832467 25 IP54 Protection for Jumper (4008321832467) LF-CONN Flex IP SC 4008321841926 25 SLIM TRACK System SLIM TRACK LF-LTS-2100 SLIM TRACK 4008321978981 40 Mounting Bracket for SLIM TRACK LF-LTS-MB 4008321979025 35 / 280 Clear SLIM TRACK Cover LF-LTS COVER C 4008321790187 40 Diffuse SLIM TRACK Cover LF-LTS-COVER-DIFFUSE 4008321979001 40 Endcap for Diffuse Cover LF-LTS-ENDCAP 4008321979049 20 / 160 Semi-Diffuse SLIM TRACK Cover LF-LTS COVER S 4008321790200 40 |
Similar Part No. - LF06P2-W4F-840-P |
|
Similar Description - LF06P2-W4F-840-P |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |