Electronic Components Datasheet Search |
|
MFL283R3S Datasheet(PDF) 6 Page - Interpoint Corporation Company |
|
MFL283R3S Datasheet(HTML) 6 Page - Interpoint Corporation Company |
6 / 14 page table 5: operating conDitionS, all moDelS, 25°c caSe, 28 Vin, 100% loaD, unleSS otherwiSe SpeciFieD. aLL MOdELS PaRaMETER CONdITIONS MIN TYP MaX uNITS LEad SOLdERINg TEMPERaTuRE 1 10 SECONdS MaX. — — 300 °C STORagE TEMPERaTuRE 1 -65 — +150 °C CaSE OPERaTINg FuLL POWER -55 — +125 °C TEMPERaTuRE aBSOLuTE 1 -55 — +135 dERaTINg OuTPuT POWER/CuRRENT 1 LINEaRLY From 100% at 125°C to 0% at 135°C ISOLaTION: INPuT TO OuTPuT OR aNY @ 500 VdC aT 25°C 100 — — Megohms PIN TO CaSE INPuT TO OuTPuT CaPaCITaNCE 1 — 150 — pF CuRRENT LIMIT 2 % OF FuLL LOad — 125 — % audIO REJECTION 1 — 50 — dB CONVERSION FREQuENCY, FREE RuN FREE RuN, -55°C TO +125°C 525 600 675 kHz SYNCHRONIZaTION IN INPuT FREQuENCY 525 — 675 kHz -55°C TO +125°C duTY CYCLE 1 40 — 60 % aCTIVE LOW — — 0.8 V aCTIVE HIgH 1 4.5 — 5.0 REFERENCEd TO INPuT COMMON IF NOT uSEd CONNECT TO INPuT COMMON SYNCHRONIZaTION OuT REFERENCEd TO INPuT COMMON IF NOT uSEd LEaVE uNCONNECTEd inHibit 1 aCTIVE LOW (OuTPuT dISaBLEd) INHIBIT PIN PuLLEd LOW — — 0.8 V do not apply a voltage to the inhibit pin. 3 INHIBIT PIN SOuRCE CuRRENT 1 — — 10 ma REFERENCEd TO INPuT COMMON inHibit 1 aCTIVE HIgH (OuTPuT ENaBLEd) INHIBIT PIN CONdITION OPEN COLLECTOR OR uNCONNECTEd do not apply a voltage to the inhibit pin. 3 OPEN INHIBIT PIN VOLTagE 1 9 — 12 V inHibit 2 aCTIVE LOW (OuTPuT dISaBLEd) INHIBIT PIN PuLLEd LOW — — 0.5 V do not apply a voltage to the inhibit pin. 3 INHIBIT PIN SOuRCE CuRRENT 1 — — 5 ma REFERENCEd TO OuTPuT COMMON inHibit 2 aCTIVE HIgH (OuTPuT ENaBLEd) INHIBIT PIN CONdITION OPEN COLLECTOR OR uNCONNECTEd do not apply a voltage to the inhibit pin. 3 OPEN INHIBIT PIN VOLTagE 1 — — 9 V Notes 1. guaranteed by qualification test and/or analysis. Not an in-line test. 2. dual outputs: The over-current limit will trigger when the sum of the currents from both outputs reaches 125% (typical value) of the maximum rated “total” current of both outputs. 3. an external inhibit interface should be used to pull the inhibits low or leave them floating. The inhibit pins can be left unconnected if not used. For mean time between failures (MTBF) contact Applications Engineering powerapps@crane-eg.com +1 425-882-3100 option 7 MFL single and dual dc-dc converters 28 VoLt input - 65 Watt www.craneae.com/interpoint Page 6 of 14 MFL Rev ad - 2016.02.19 Crane Aerospace & Electronics Power Solutions |
Similar Part No. - MFL283R3S_16 |
|
Similar Description - MFL283R3S_16 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |