Electronic Components Datasheet Search |
|
TPS62410DRCR Datasheet(PDF) 3 Page - Texas Instruments |
|
|
TPS62410DRCR Datasheet(HTML) 3 Page - Texas Instruments |
3 / 36 page Thermal Pad EN2 9 MODE/DATA 2 SW2 10 ADJ2 1 GND 8 VIN 3 SW1 6 DEF_1 5 EN1 7 FB1 4 TPS62410 www.ti.com SLVS737A – FEBRUARY 2007 – REVISED JULY 2015 5 Pin Configuration and Functions DRC Package 10-Pin VSON Top View Pin Functions PIN I/O DESCRIPTION NAME NO. Input to adjust output voltage of converter 2. In adjustable version (TPS62410) connect an external ADJ2 1 I resistor divider between VOUT2, this pin and GND to set output voltage between 0.6 V and VIN. If EasyScale™ interface is used for converter 2, this pin must be directly connected to the output. This Pin has 2 functions: 1. Operation mode selection: With low level, power-save mode is enabled where the device operates in PFM mode at light loads and enters automatically PWM mode at heavy loads. Pulling this PIN to High forces the device to operate in PWM mode over the whole load range. MODE/DATA 2 I 2. EasyScale™ interface function: One wire serial interface to change the output voltage of both converters. The pin has an open-drain output to provide an acknowledge condition if requested. The current into the open-drain output stage may not exceed 500 μA. The interface is active if either EN1 or EN2 is High. VIN 3 I Supply voltage, connect to VBAT, 2.5 V to 6 V Direct feedback voltage sense input of converter 1, connect directly to VOUT1. An internal feed forward FB1 4 I capacitor is connected between this pin and the error amplifier. In case of fixed output voltage versions or when the Interface is used, this pin is connected to an internal resistor divider network. This pin defines the output voltage of converter 1. The pin acts in TPS62410 as an analog input for output voltage setting through external resistors. In fixed default output voltage versions this pin is a digital input to select between two fixed default output voltages. DEF_1 5 I/O In TPS62410 an external resistor network needs to be connected to this pin to adjust the default output voltage. SW1 6 — Switch pin of converter1. Connected to inductor 1 EN1 7 I Enable input for converter1, active high GND 8 I GND for both converters, this pin should be connected with the PowerPAD EN2 9 I/O Enable input for converter 2, active high SW2 10 — Switch pin of converter 2. Connected to inductor 2 PowerPAD™ — — Connect to GND Copyright © 2007–2015, Texas Instruments Incorporated Submit Documentation Feedback 3 Product Folder Links: TPS62410 |
Similar Part No. - TPS62410DRCR |
|
Similar Description - TPS62410DRCR |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |