Electronic Components Datasheet Search |
|
PCA9533 Datasheet(PDF) 2 Page - NXP Semiconductors |
|
PCA9533 Datasheet(HTML) 2 Page - NXP Semiconductors |
2 / 18 page Philips Semiconductors Product data sheet PCA9533 4-bit I2C LED dimmer 2 2004 Oct 01 FEATURES • 4 LED drivers (on, off, flashing at a programmable rate) • 2 selectable, fully programmable blink rates (frequency and duty cycle) between 0.591 Hz and 152 Hz (1.69 seconds and 6.58 milliseconds) • 256 brightness steps • Input/outputs not used as LED drivers can be used as regular GPIOs • Internal oscillator requires no external components • I2C interface logic compatible with SMBus • Internal power-on reset • Noise filter on SCL/SDA inputs • 4 open drain outputs directly drive LEDs to 25 mA • Edge rate control on outputs • No glitch on power-up • Supports hot insertion • Low stand-by current • Operating power supply voltage range of 2.3 V to 5.5 V • 0 to 400 kHz clock frequency • ESD protection exceeds 2000 V HBM per JESD22-A114, 150 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101 • Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA • Packages offered: SO8, TSSOP8 (MSOP8) DESCRIPTION The PCA9533 is a 4-bit I2C and SMBus I/O expander optimized for dimming LEDs in 256 discrete steps for Red/Green/Blue (RGB) color mixing and back light applications. The PCA9533 contains an internal oscillator with two user programmable blink rates and duty cycles coupled to the output PWM. The LED brightness is controlled by setting the blink rate high enough (> 100 Hz) that the blinking cannot be seen and then using the duty cycle to vary the amount of time the LED is on and thus the average current through the LED. The initial setup sequence programs the two blink rates/duty cycles for each individual PWM. From then on, only one command from the bus master is required to turn individual LEDs ON, OFF, BLINK RATE 1 or BLINK RATE 2. Based on the programmed frequency and duty cycle, BLINK RATE 1 and BLINK RATE 2 will cause the LEDs to appear at a different brightness or blink at periods up to 1.69 second. The open drain outputs directly drive the LEDs with maximum output sink current of 25 mA per bit and 100 mA per package. To blink LEDs at periods greater than 1.69 second the bus master (MCU, MPU, DSP, chipset, etc.) must send repeated commands to turn the LED on and off as is currently done when using normal I/O Expanders like the Philips PCF8574 or PCA9554. Any bits not used for controlling the LEDs can be used for General Purpose Parallel Input/Output (GPIO) expansion which provides a simple solution when additional I/O is needed for ACPI power switches, sensors, pushbuttons, alarm monitoring, fans, etc. Power-On Reset (POR) initializes the registers to their default state causing the bits to be set HIGH (LED off). Due to pin limitations, the PCA9533 is not featured with hardware address pins. The PCA9533/01 and the PCA9533/02 have different fixed I2C addresses allowing operation of both on the same bus. PIN CONFIGURATION 1 2 3 45 6 7 8 LED0 LED1 LED2 VSS VDD SDA SCL LED3 SW01035 Figure 1. Pin configuration PIN DESCRIPTION PIN NUMBER SYMBOL FUNCTION 1 LED0 LED driver 0 2 LED1 LED driver 1 3 LED2 LED driver 2 4 VSS Supply ground 5 LED3 LED driver 3 6 SCL Serial clock line 7 SDA Serial data line 8 VDD Supply voltage |
Similar Part No. - PCA9533 |
|
Similar Description - PCA9533 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |