Electronic Components Datasheet Search |
|
XE1414 Datasheet(PDF) 11 Page - List of Unclassifed Manufacturers |
|
XE1414 Datasheet(HTML) 11 Page - List of Unclassifed Manufacturers |
11 / 18 page XECOM (11) XE1414C XE1414C AT COMMANDS (continued) \Bn - Transmit Break - AT\Bn selects the duration of the break signal sent. Break = n x 100 msec. \Kn - Break control - AT\Kn determines how the modem will handle a break signal received from the host. Break received from host in data transfer mode. n=0 Enter on-line command mode; do not transmit break n=1 Purge buffers, immediately transmit break n=2 Same as n=0 n=3 Immediately send break n=4 Same as n=0 n=5 Send break in sequence with data * Break received from the host during the on-line com- mand mode. n=0 Purge buffers, immediately transmit break n=1 Same as n=0 n=2 Immediately send break n=3 Same as n=2 n=4 Send break in sequence with data n=5 same as n=4 * Break received from modem during a non-error cor- rected link n=0 Purge buffers, Immediately send break to host n=1 same as n=0 n=2 Immediately send break to the host n=3 Same as n=2 n=4 Send break in sequence with data. n=5 Same as n=2* \Nn - Error Control Selection - AT\Nn determines how the modem will handle error control negotiations. n=0 Normal mode, no error correction n=1 Direct mode, no buffering, no error correction n=2 Reliable mode, error correction required n=3 V.42 Auto-reliable mode, accept either an error controlled or non-error controlled link* n=4 V.42 Reliable mode, LAPM required n=5 MNP required /V<value> - Single Line Connect Messages - This command allows users to select single line connect messages in the for- mat shown below. <DTE Speed> <Modulation> <Protocol> <Compression> <Line Speed> <Voice & Data> n=0 No single Line Connect Messages n=1 Issue a complete response in a single line -Kn - MNP Extended Services - AT-Kn determines how the modem handles MNP10. n=0 No LAPM to MNP10 conversion n=1 LAPM to MNP10 conversion* n=2 LAPM to MNP10 conversion no MNP Extended Service during V.42 LAPM answer mode detect. +GCI=nn - Country Code - The AT+GCI command sets the country code to be sued by the modem. See the country listing on Page 6 for the appropriate country code for your application. The Default country code is B5, United States. +MS - Select Modulation - AT+MS sets the modulation and data rates to be supported by the modem. The format for the +MS command is shown below. AT+MS=a, b, c, d, e, f<CR> a - modulation type B103 - Bell 103 (300 BPS) B212 - Bell 212A (1200 BPS) V21 - V.21 (300 BPS) V22 - V.22 (1200 BPS) V.22B - V.22bis (1200 or 2400 BPS) V23 - V.23 (1200 Tx / 75 RX or 75 Tx / 1200 Rx) V32 - V.32 (4800 or 9600 BPS) V32B - V.32bis (4800 to 14,400 BPS) b - Automode Detection 0 - Automatic Negotiation Disabled 1 - Automatic Negotiation Enabled c - Minimum Receive Data Rate (300 to 14400 BPS) d - Maximum Receive Data Rate (300 to 14400 BPS) e - Minimum Transmit Data Rate (300 to 14400 BPS) f - Maximum Transmit Data Rate (300 to 14400 BPS) Default: AT+MS=V32B, 1, 300, 300, 300, 14400 |
Similar Part No. - XE1414 |
|
Similar Description - XE1414 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |