4

COMMERCIALANDINDUSTRIAL

TEMPERATURERANGES

IDT72261LA/72271LA SuperSync FIFO™

16,384 x 9 and 32,768 x 9

Symbol

Name

I/O

Description

DataInputs

I

Data inputs for a 9-bit bus.

MRS

MasterReset

I

MRS initializes the read and write pointers to zero and sets the output register to all zeroes.

During Master Reset, the FIFO is configured for either FWFT or IDT Standard mode, one of

two programmable flag default settings, and serial or parallel programming of the offset settings.

PRS

Partial Reset

I

PRS initializes the read and write pointers to zero and sets the output method (serial or parallel),

and programmable flag settings are all retained.

RT

Retransmit

I

RT asserted on the rising edge of RCLK initializes the READ pointer to zero, sets the EF flag to

LOW (OR to HIGH in FWFT mode) temporarily and does not disturb the write pointer, programming

method, existing timing mode or programmable flag settings. RT is useful to reread data from the

first physical location of the FIFO.

FWFT/SI

First Word Fall

I

During Master Reset, selects First Word Fall Through or IDT Standard mode. Through/Serial

In After Master Reset, this pin functions as a serial input for loading offset registers

WCLK

Write Clock

I

When enabled by WEN, the rising edge of WCLK writes data into the FIFO and offsets into

the programmable registers for parallel programming, and when enabled by SEN, the rising

edge of WCLK writes one bit of data into the programmable register for serial programming.

WEN

Write Enable

I

WEN enables WCLK for writing data into the FIFO memory and offset registers.

RCLK

Read Clock

I

When enabled by REN, the rising edge of RCLK reads data from the FIFO memory and offsets

fromtheprogrammableregisters.

REN

Read Enable

I

REN enables RCLK for reading data from the FIFO memory and offset registers.

OE

OutputEnable

I

SEN

SerialEnable

I

SENenablesserialloadingofprogrammableflagoffsets.

LD

Load

I

During Master Reset, LD selects one of two partial flag default offsets (127 or 1,023) and determines

the flag offset programming method, serial or parallel. After Master Reset, this pin enables writing to

andreadingfromtheoffsetregisters.

DC

Don't Care

I

FF/IR

Full Flag/

O

In the IDT Standard mode, the FF function is selected. FF indicates whether or not the FIFO memory

Input Ready

is full. In the FWFT mode, the IR function is selected. IR indicates whether or not there is space

available for writing to the FIFO memory.

EF/OR

EmptyFlag/

O

In the IDT Standard mode, the EF function is selected. EF indicates whether or not the FIFO memory

OutputReady

is empty. In FWFT mode, the OR function is selected. OR indicates whether or not there is valid data

availableattheoutputs.

PAF

Programmable

O

PAF goes LOW if the number of words in the FIFO memory is more than word capacity of the FIFO

Almost-FullFlag

minusthefulloffsetvaluem,whichisstoredintheFullOffsetregister.Therearetwopossibledefault

values for m: 127 or 1,023.

PAE

Programmable

O

PAE goes LOW if the number of words in the FIFO memory is less than offset n, which is stored in the

Almost-EmptyFlag

Empty Offset register. There are two possible default values for n: 127 or 1,023. Other values for n

can be programmed into the device.

HF

Half-FullFlag

O

HF indicates whether the FIFO memory is more or less than half-full.

DataOutputs

O

Data outputs for a 9-bus

Power

+5 Volt power supply pins.

GND

Ground

Groundpins.

PIN DESCRIPTION