 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
72845LB25BGG Datasheet(PDF) 11 Page - Integrated Device Technology |
|
||||||||||||||||||||||||||||||
72845LB25BGG Datasheet(HTML) 11 Page - Integrated Device Technology |
|
|
11 / 26 page  11 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES IDT72805LB/72815LB/72825LB/72845LB CMOS Dual SyncFIFOTM 256 x 18, 512 x 18, 1,024 x 18, and 4,096 x 18 WhentheLDpinisLOWandWENisHIGH,theWCLKinputisdisabled;then asignalatthisinputcanneitherincrementthewriteoffsetregisterpointer,nor execute a write. The contents of the offset registers can be read on the output lines when the LD pin is set LOW and REN is set LOW; then, data can be read on the LOW-to-HIGH transition of the Read clock (RCLK). The act of reading the control registers employs a dedicated read offset register pointer. (The read and write pointers operate independently). Offset register content can be read out in the IDT Standard mode only. It is inhibited in the FWFT mode. A read and a write should not be performed simultaneously to the offset registers. FIRST LOAD (FLA/FLB) For the single device mode, see Table I for additional information. In the Daisy Chain Depth Expansion configuration, FLA/FLB is grounded to indicate it is the first device loaded and is set to HIGH for all other devices in the Daisy Chain. (See Operating Configurations for further details.) WRITE EXPANSION INPUT (WXIA/WXIB) This is a dual purpose pin. For single device mode, see Table I for additional information. WXIA/WXIB is connected to Write Expansion Out (WXOA/WXOB) of the previous device in the Daisy Chain Depth Expansion mode. READ EXPANSION INPUT (RXIA/RXIB) This is a dual purpose pin. For single device mode, see Table I for additionalinformation.RXIA/RXIBisconnectedtoReadExpansionOut(RXOA/ RXOB) of the previous device in the Daisy Chain Depth Expansion mode. OUTPUTS: FULL FLAG/INPUT READY (FFA/IRA, FFB/IRB) This is a dual purpose pin. In IDT Standard mode, the Full Flag (FFA/ FFB) function is selected. When the FIFO is full, FF will go LOW, inhibiting further write operations. When FF is HIGH, the FIFO is not full. If no reads are performed after a reset, FF will go LOW after D writes to the FIFO. D = 256 writes for the IDT72805LB, 512 for the IDT72815LB, 1,024 for the IDT72825LB and 4,096 for the IDT72845LB. In FWFT mode, the Input Ready (IRA/IRB) function is selected. IR goes LOW when memory space is available for writing in data. When there is no longer any free space left, IR goes HIGH, inhibiting further write operations. IR will go HIGH after D writes to the FIFO. D = 257 writes for the IDT72805, 513 for the IDT72815, 1,025 for the IDT72825 and 4,097 for the IDT72845.NotethattheadditionalwordinFWFTmodeisduetothecapacity ofthememoryplusoutputregister. FF/IR is synchronous and updated on the rising edge of WCLK. EMPTY FLAG/OUTPUT READY (EFA/ORA, EFB/ORB) This is a dual purpose pin. In the IDT Standard mode, the Empty Flag (EFA/EFB) function is selected. When the FIFO is empty, EF will go LOW, inhibiting further read operations. When EF is HIGH, the FIFO is not empty. In FWFT mode, the Output Ready (ORA/ORB) function is selected. OR goes LOW at the same time that the first word written to an empty FIFO appears valid on the outputs. OR stays LOW after the RCLK LOW to HIGH transition that shifts the last word from the FIFO memory to the outputs. OR goes HIGH only with a true read (RCLK with REN = LOW). The previous data stays at the outputs, indicating the last word was read. Further data reads are inhibited until OR goes LOW again. EF/OR is synchronous and updated on the rising edge of RCLK. PROGRAMMABLE ALMOST-FULL FLAG (PAFA/PAFB) The Programmable Almost-Full flag (PAFA/PAFB) will go LOW when FIFO reaches the almost-full condition. In IDT Standard mode, if no reads are performed after Reset (RS), the PAFwill go LOW after (256-m) writes for the IDT72805LB, (512-m) writes for the IDT72815LB, (1,024-m) writes for theIDT72825LBand(4,096–m)writesfortheIDT72845LB.Theoffset“m”is definedintheFullOffsetregister. In FWFT mode, if no reads are performed, PAF will go LOW after (257- m) writes for the IDT72805LB, (513-m) writes for the IDT72815LB, (1,025- m)writesfortheIDT72825LBand(4,097-m)writesfortheIDT72845LB.The default values for m are noted in Table 1 and 2. IfasynchronousPAFconfigurationisselected,thePAFisassertedLOW ontheLOW-to-HIGHtransitionoftheWriteClock(WCLK).PAFisresettoHIGH ontheLOW-to-HIGHtransitionoftheReadClock(RCLK).IfsynchronousPAF configuration is selected (see Table I), the PAF is updated on the rising edge ofWCLK. PROGRAMMABLE ALMOST-EMPTY FLAG (PAEA/PAEB) The PAE flag will go LOW when the FIFO reads the almost-empty condition. In IDT Standard mode, PAE will go LOW when there are n words or less in the FIFO. In FWFT mode, the PAE will go LOW when there are n+1 words or less in the FIFO. The offset “n” is defined as the Empty offset. The default values for n are noted in Table 1 and 2. If asynchronous PAE configuration is selected, the PAE is asserted LOW on the LOW-to-HIGH transition of the Read Clock (RCLK). PAE is reset to HIGH on the LOW-to-HIGH transition of the Write Clock (WCLK). If synchronous PAE configuration is selected (see Table I), the PAE is updated on the rising edge of RCLK. WRITE EXPANSION OUT/HALF-FULL FLAG (WXOA/HFA, WXOB/HFB) This is a dual-purpose output. In the Single Device and Width Expansion mode, when Write Expansion In (WXIA/WXIB) and/or Read Expansion In (RXIA/RXIB) are grounded, this output acts as an indication of a half-full memory. After half of the memory is filled, and at the LOW-to-HIGH transition of the next write cycle, the Half-Full flag goes LOW and will remain set until the difference between the write pointer and read pointer is less than or equal to one half of the total memory of the device. The Half-Full flag (HFA/HFB) is then reset to HIGH by the LOW-to-HIGH transition of the Read Clock (RCLK). The HF is asynchronous. In the Daisy Chain Depth Expansion mode, WXI is connected to WXO of the previous device. This output acts as a signal to the next device in the Daisy Chain by providing a pulse when the previous device writes to the last location of memory. READ EXPANSION OUT (RXOA/RXOB) In the Daisy Chain Depth Expansion configuration, Read Expansion In (RXIA/RXIB) is connected to Read Expansion Out (RXOA/RXOB) of the previous device. This output acts as a signal to the next device in the Daisy Chain by providing a pulse when the previous device reads from the last location of memory. DATA OUTPUTS (Q0-Q17, QB0-QB17) Q0-Q17 are data outputs for 18-bit wide data. |
Similar Part No. - 72845LB25BGG |
|
Similar Description - 72845LB25BGG |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
