Electronic Components Datasheet Search |
|
TAS5110IDAP Datasheet(PDF) 7 Page - Texas Instruments |
|
TAS5110IDAP Datasheet(HTML) 7 Page - Texas Instruments |
7 / 20 page TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 7 www.ti.com functional description PWM H-bridge state control The digital interface control signals consists of PWM_AP, PWM_AM, PWM_BP, and PWM_BM. These signals are a complementary differential signal format for the A-side half-bridge and the B-side half-bridge. bootstrapped gate drive The TAS5110 includes two dedicated bootstrapped power supplies. A bootstrap capacitor is connected between the individual bootstrap pin and the associated output. For example, a capacitor is connected between the BOOTSTRAPA pin and OUTPUTA pin, and another capacitor is connected between the BOOTSTRAPB pin and the OUTPUTB pin. The bootstrap power supply minimizes the number of high voltage power supply levels externally supplied to the system while providing a low-noise supply level for driving the high-side N-channel DMOS transistors. low-dropout voltage regulator Two on-chip low-dropout voltage regulators (LDO) are provided to minimize the number of external power supplies needed for the system. These voltage regulators are for internal circuits only and cannot be used for external circuitry. Each LDO is dedicated to a half-bridge and its gate driver. An LDO output capacitor is connected between the individual LDO output pin and the associated output return. For example, a capacitor is connected between the LDROUTA pin and PVSS pin, and another capacitor is connected between the LDROUTB pin and PVSS pin. high-current H-bridge output stage The positive outputs of the H-bridge are the two OUTPUTA pins. The negative outputs of the H-bridge are the two OUTPUTB pins. The logic for the input command to H-bridge outputs is described in the H-bridge output mapping section below. When the TAS5110 is in the normal mode, as seen in the H-bridge output mapping tables, the outputs are decoded from the inputs. However, the TAS5110 is immediately shut down if any of the following error conditions occur: over-current, over-temperature, low regulator output voltage, or an illegal PWM input state is applied. For these conditions, the outputs are set to the appropriate disabled state as specified in the H-bridge output mapping section, and the SHUTDOWN pin is set low. H-bridge output mapping The A-side half-bridge output is designed to the following truth table: INPUTS OUTPUTS DESCRIPTION RESET PWDN PWM_AP PWM_AM SHUTDOWN OUTPUTA DESCRIPTION X X X X 0 0 or Hi-Z† Shutdown X 0 X X 1 Hi-Z Powerdown 0 1 X X 1 0 Reset 1 1 0 0 0 0 Shutdown 1 1 0 1 1 0 Normal 1 1 1 0 1 1 Normal 1 1 1 1 0 0 Shutdown † Output is 0 for low voltage, over temperature, and illegal input. Hi-Z is for over current. |
Similar Part No. - TAS5110IDAP |
|
Similar Description - TAS5110IDAP |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |