Electronic Components Datasheet Search |
|
H40B-4000-ABZC-15V Datasheet(PDF) 2 Page - List of Unclassifed Manufacturers |
|
H40B-4000-ABZC-15V Datasheet(HTML) 2 Page - List of Unclassifed Manufacturers |
2 / 2 page Tel: 805-968-0782 /800-350-2727 | Fax: 805-968-3154 / 800-960-2726 | 7230 Hollister Ave., Goleta, CA 93117-2807 www.beisensors.com H40 Shock Proof Optical Encoder Dimensions Tables Figure 1 Notes 1, 2, 3, 5, 6, 7, 8, 10, 13, 16, 20, 24, 25, 26, 30, 32, 33, 34, 36, 37, 40, 45, 48, 50, 51, 56*, 60, 64, 66, 72, 75, 80, 86, 88, 90, 100, 102, 120, 122,125, 127, 128, 132, 144, 148, 150, 158, 160, 175, 176, 180, 187, 192, 200, 202, 204*, 217, 220, 240, 250, 254, 255, 256, 264*, 274, 280, 283, 288, 292, 300, 312, 320, 321, 325, 360, 366, 372, 375, 377, 380, 381, 384, 385, 393, 400, 430, 432, 450, 462, 480, 490, 500, 502, 508, 512, 522, 530, 550, 560*, 576, 598, 600, 604, 625, 628, 635, 638, 640, 660, 672, 676, 680, 687, 690, 700, 720, 725, 735, 740, 744, 748, 750, 762, 768, 780, 785, 800, 812, 825, 850, 864, 878, 888, 900, 912, 914, 938, 942, 955, 960, 1000, 1016, 1024, 1030, 1035, 1036, 1040, 1054, 1056, 1074, 1076, 1080,1088, 1100, 1101, 1125, 1136, 1200, 1237, 1250, 1257, 1270, 1280, 1300, 1314, 1332, 1333, 1390, 1400, 1414, 1427, 1440, 1484, 1500, 1562, 1570, 1596, 1600, 1650, 1666, 1718, 1745, 1774, 1800, 1840*, 1850, 1855, 1875, 1894, 1920, 1952, 1968, 1979, 1995, 2000, 2048, 2080, 2094, 2100, 2160, 2164, 2199, 2200, 2250, 2356, 2400, 2485, 2500, 2514, 2519, 2540, 3000, 3125, 3600, 4000, 4096, 5000 *AB or ABC output only. NOTE: Resolutions up to 72,000 are available. 4.06 4.00 2.56 1/4-20 UNC-2B 0.50 DEEP (4) ON A 3.0 DIA B.C. 2.03 9.36 2.1 2.39 4.00 1.30 4.75 3.56 DIA 1.56 0.75 0.6248 0.6244 DIA 0.59 2.45 2.146 ± 0.005 COUPLING ACCESS PORT 1/2 - NPSF (DRYSEAL) STRAIGHT PIPE THREADS NOTE: THIS WIRING PORT WILL BE SEALED WITH A PIPE PLUG IF THE EM OR EC OPTION IS SPECIFIED .281 DIA (4) 1/4-20 UNC-2B 0.50 DEEP (4) ON A Ø 3.0 B.C. Ø 0.6248 0.6244 Ø .281 (4) Ø 3.56 Ø 4.5 1/4-20 UNC-2B 0.50 DEEP (4) ON A Ø 3.0 B.C. Ø 0.6248 0.6244 Ø .281 (4) Ø 3.56 Ø 4.5 1/4-20 UNC-2B 0.50 DEEP (4) ON A Ø 3.0 B.C. Ø 0.6248 0.6244 Ø .281 (4) Ø 3.56 Ø 4.5 1/4-20 UNC-2B 0.50 DEEP (4) ON A Ø 3.0 B.C. Ø 0.6248 0.6244 Ø .281 (4) Ø 3.56 Ø 4.5 H40B Field Replaceable Coupling & Bearing Assembly Rear View H40A SPEED (RPM) Bearing Life vs. Speed at Various Radial Loads Incremental 8-Bit Absolute* Latch and Interrogate are optional *or SELECT on Dual Count encoders GRAY NATURAL TERMINAL CODE BINARY NUMBER G0 20 1 G1 21 2 G2 22 3 G3 23 4 G4 24 5 G5 25 6 G6 26 7 G7 27 8 SPARE 9 SPARE 10 LATCH 11 INTERROGATE 12 SPARE 13 +VDC 14 0V (COMMON) 15 CASE GROUND 16 TERMINAL FUNCTION A CHANNEL A B B Z Z V +VDC G GROUND (0V) CG CASE GROUND A A B B Z Z S SPARE* Output Functions Table 1 Incremental Output Terminations Disc Resolutions for Incremental Encoder Model H40 Table 2 Table 3 1. Mounting is usually done either using the D-style square flange mount, E- or G-style servo mounts, or one of the standard face mounts, F1 for example. Consult factory for additional face mount options. 2.The shaft seal is recommended in virtually all installations. The most common excep- tions are applications requiring a very low starting torque or those requiring operation at both high temperature and high speed. 3. Non-standard index widths and multiple indices are available by special order. Consult factory. 4. Complementary outputs are recommended for use with line driver type (source/ sink) outputs. When used with differential receivers, this combination provides a high degree of noise immunity. 5. Output IC’s: Output IC’s are available as either Line Driver (LD) or NPN Open Collector (OC) types. Open Collectors require pull-up resistors, resulting in higher output source impedance (sink impedance is similar to that of line drivers). In general, use of a Line Driver style output is recommended. Line Drivers source or sink current and their lower impedance mean better noise immunity and faster switching times. Warning: Do not connect any line driver outputs directly to circuit common/OV, which may damage the driver. Unused outputs should be isolated and left floating. Our applications specialists would be pleased to discuss your system requirements and the compatibility of your receiving electronics with Line Driver type outputs. 28V/V: Multi-voltage Line Driver (7272*): 100 mA source/sink. Input voltage 5 to 28 VDC +/- 5% standard (Note: Vout = Vin). This driver is TTL compatible when used with 5 volt supply. Supply lines are protected against overvoltage to 60 volts and reverse voltage. Outputs are short circuit protected for one minute. Supply current is 120 mA typical (plus load current). This is the recommended replacement for 3904R and 7406R open collector outputs with internal pullup resistors. It is also a direct replacement for any 4469, 88C30, 8830 or 26LS31 line driver 28V/5: Multi-voltage Line Driver (7272*): 100 mA source/sink. Input voltage 5 to 28 VDC +/- 5% standard, internally regulated with 5V (TTL compatible) logic out. Supply lines are protected against overvoltage to 60 volts and reverse voltage. Outputs are short circuit protected for one minute. Supply current is 90 mA typical (plus load current). 15V/V: Multi-voltage Line Driver (4469*): 100 mA source/sink. Input voltage 5 to 15 VDC +/- 5% standard (Note: Vout = Vin). TTL compatible when used with 5 volt supply. Supply lines are protected against overvoltage to 60 volts and reverse voltage. Outputs are short circuit protected for one minute. Supply current is 90 mA typical (plus load cur- rent). This is a direct replacement for the 4469 Line Driver. 28V/OC: NPN Open Collector (3904*, 7273*). Current sink of 80 mA max. Current sourced by external pull- up resistor. Output can be pulled up to voltage other than supply voltage (30 V max). Input voltage 5 to 28 VDC +/- 5% standard. Supply current is 120 mA typical. This replaces prior IC’s with designations of 3904, 7406, 3302, 681 and 689. 5V/OCR, 15V/OCR, 24V/OCR: Open Collector (3904R*, 7406R*, 7273R*): Current sink of 70 mA max. Includes internal pull-ups sized at approximately 100 ohms/volt. Max current source is 10 mA. Supply current is 100 mA typical, 120 mA with internal pull-ups. The 5V/ OCR, 15V/OCR and 24V/OCR are often replaced by the 28V/V in system upgrades. 3904, 3904R, 4469, 5V/V, 5V/OC, 5V/OCR, 9V/OC: Intrinsically safe line driver and open collector outputs. These drivers are specific to intrinsically safe encoders, and are installed per the appropriate control drawings listed in Table 2.1 on page 48 of the 2008 BEI Specifying Guide. 6. Special –S at the end of the model number is used to define a variety of non-standard features such as special shaft lengths, voltage options, or special testing. Please consult the factory to discuss your special requirements. 7. Higher frequency response may be available. Please consult with the factory. 8. Extended temperature ratings are available in the following ranges: -40 to 70°C, -40 to 85°C, –20 to 105°C and –40 to 105°C depending on the particular model. Some models can operate down to -55°C. Extended temperature ranges can affect other performance factors. Consult with factory for more specific information. 9. Mating straight plug receptacles may be ordered from the factory: For M12 use MS3116F12-10S, For M14 use MS3106F14S-6S For M14/19 use MS3116J14-19S, For M16 use MS3106F16S-1S For M18 use MS3106F18-1S, For M20 use MS3106F20-29S * Products manufactured prior to April 2007 used the line driver IC number instead of voltage output in model number. M16 CONNECTOR CHANNELS DESIGNATED IN MODEL NUMBER PIN ABZ ABC A A A B B B C Z A D +V(SUPPLY VOLTAGE) E — B F OV (CIRCUIT COMMON) G CASE GROUND (CG) M18 CONNECTOR PIN CHANNEL A CHANNEL A B B C Z D +VDC F GROUND (OV) G CASE GROUND H A I B J Z |
Similar Part No. - H40B-4000-ABZC-15V |
|
Similar Description - H40B-4000-ABZC-15V |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |