Electronic Components Datasheet Search |
|
408-10390 Datasheet(PDF) 8 Page - TE Connectivity Ltd |
|
408-10390 Datasheet(HTML) 8 Page - TE Connectivity Ltd |
8 / 18 page 408-10390 Rev M1 8 of 18 NOTE Adjustment of the stripper may be required when moving the applicator between bench and leadmaker applications. 4. APPLICATOR LOADING AND UNLOADING Some terminal strips require the use of a terminal lubricant. Wick-type lubricators apply lubricant to the terminal strip as it feeds into the applicator. Terminal lubricants reduce tooling wear and help reduce damage to the plating on some terminals. Ocean applicator lubricator assembly PN 2119955-2 is available. CAUTION Depending on the final use of the crimped terminal, terminal lubricators are not always recommended. To determine if your applications warrant the use of a terminal lubricator, contact your field representative. If your application warrants the use of a terminal lubricator, the recommended lubricant is Stoner Mechanical Lubricant E807 available from Stoner, Inc. Call 1 –800–227–5538 or visit www.stonersolutions.com. 4.1. Terminal Strip Loading NOTE Before loading terminal strip in applicator, make sure that the installed applicator is the right one for the terminal to be applied. Compare the terminal part number on the reel with the numbers listed on the applicator parts list. 1. Turn off, and disconnect, the power to the machine. 2. Make sure that the ram assembly is all the way up. If necessary, hand-cycle the machine to raise the ram. Refer to the machine customer manual. 3. Remove the applicator guard assembly. 4. Raise the stock drag by turning the drag release lever upward. Remove a length of the terminal strip left in the applicator by grasping the terminals at the strip guide entry, raising the feed pawl, and pulling the strip straight out of the applicator. 5. With the reel of terminals installed on the reel support, feed the terminal strip into the applicator between the strip guides. NOTE Make sure that the terminal strip enters the strip guides with the terminal wire barrel first and the wire barrel open side up. 6. Raise the feed pawl, and continue to feed the terminal strip until the lead terminal is over the anvil and the feed pawl engages the terminal in the proper position. 7. If terminals are post-feed, lift the feed pawl and pull the strip back one terminal length. The lead terminal will then be moved over the anvil on the downward stroke of the ram assembly. Make sure that the tip of the feed pawl is in the feed hole of the carrier strip. NOTE Some carrier strips have additional holes which are not used for feed purposes. 8. Hand-cycle the machine several times to make sure the applicator is properly adjusted as described in Section 5. 9. Re-install the applicator guard assembly. 4.2. Terminal Strip Unloading 1. Cut the terminal strip one or two terminals from the end of the applicator. NOTE The applicator should never be unloaded unnecessarily. A section of terminal strip should always be left in the unit. Since it is not necessary to remove the strip section for cleaning, lubrication, or repair, it should only be removed as a part of the loading procedure. 2. If terminals are post-feed, turn the drag release lever upward to raise the stock drag, lift the feed pawl, and move the lead terminal over the anvil. |
Similar Part No. - 408-10390 |
|
Similar Description - 408-10390 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |