Electronic Components Datasheet Search |
|
D2F-FL-A Datasheet(PDF) 5 Page - Omron Electronics LLC |
|
D2F-FL-A Datasheet(HTML) 5 Page - Omron Electronics LLC |
5 / 6 page 5 D2F Ultra Subminiature Basic Switch D 2 F Note 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. Note 2. The operating characteristics are for operation in the A direction ( ). Precautions ★Please refer to "Basic Switches Common Precautions" for correct use. ●Soldering • Terminal connection When soldering, make sure that the temperature of the soldering iron tip is not higher than 300°C, and complete the soldering within 3 seconds. Do not apply any external force for 1 minute after soldering. Soldering at an excessively high temperature or soldering for more than 3 seconds may deteriorate the characteristics of the Switch. • Connecting to PCB terminal Boards When using automatic soldering baths, we recommend soldering at 260°C ±5°C within 5 seconds. Make sure that the liquid surface of the solder does not flow over the edge of the board. When soldering terminals manually, perform soldering within 3 seconds at iron tip temperature not higher than 350°C. Do not apply any external force for at least 1 minute after soldering. When applying solder, keep the solder away from the case of the Switch and do not allow solder or flux to flow into the case. ●Mounting Use M2 mounting screws with plane washers or spring washers to securely mount the Switch. Tighten the screws to a torque of 0.08 to 0.1 N·m {0.8 to 1 kgf·cm}. ●Using Micro Loads Using a model for ordinary loads to open or close the contact of a micro load circuit may result in faulty contact. Use models that operate in the following range. However, even when using micro load models within the following operating range, if inrush current occurs when the contact is opened or closed, it may increase the contact wear and so decrease durability. Therefore, insert a contact protection circuit where necessary. The minimum applicable load is the N-level reference value. This value indicates the malfunction reference level for the reliability level of 60% ( λ60). (JIS C5003) The equation, λ60=0.5×10-6/operation, indicates that the estimated malfunction rate is less than operations with a reliability level of 60%. ●Hinge Roller Lever Models D2F-L2 @ D2F-01L2 @ D2F-FL2 @ D2F-01FL2 @ Operating Characteristics Model D2F-L2 @ D2F-01L2 @ D2F-FL2 @ D2F-01FL2 @ Operating Force OF Max. Releasing Force RF Min. 0.78 N {80 gf} 0.05 N {5 gf} 0.39 N {40 gf} 0.02 N {2 gf} Overtravel OT Min. Movement Differential MD Max. 0.55 mm 0.5 mm 0.55 mm 0.5 mm Free Position FP Max. Operating Position OP 16.5 mm 13±2 mm (10) 4 12.8 t=0.3 *1 (4.6) *1. Stainless-steel lever *2. Polyacetal resin roller OP 4 FP 4.8 dia. ×2.8 *2 A Cautions Correct Use 1 2,000,000 30 24 12 5 0 1 10 100 1,000 Current (mA) 0.1 1 mA Operating range for general-load models D2F 16.6 mA 0.16 mA 100 mA Operating range for micro load models D2F-01 |
Similar Part No. - D2F-FL-A |
|
Similar Description - D2F-FL-A |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |