 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
LMC1982CIN Datasheet(PDF) 11 Page - National Semiconductor (TI) |
|
|
||||||||||||||||||||||||||||||
LMC1982CIN Datasheet(HTML) 11 Page - National Semiconductor (TI) |
|
|
11 / 14 page  Application Information (Continued) As shown in Table 1, loudness and enhanced stereo are controlled through the same address. It is important to re- member to set both functions to the correct value any time either of these functions is updated. ENHANCED STEREO The LMC1982 has an enhanced stereo effect that can be achieved by cross-coupling reverse phase information be- tween the left and right stereo channels. This feature can help improve the apparent stereo channel separation when, because of cabinet or equipment limitations, the left and right speakers are closer to each other than optimum. Enhanced stereo is created by connecting an external fre- quency shaping RC network between the OUTPUT opera- tional amplifiers’ inverting inputs through an internal CMOS switch (see Figure 6). The external network couples 60% of each channel’s output to the opposite channel’s inverting in- put. This cancels a portion of the signal common to both channels. The desired 60% cross-coupling is accomplished through the internal 6.5 k Ω feedback resistor and an external 10 kΩ resistor. Bass frequency cancellation is prevented by using a 0.047 µF coupling capacitor to couple only frequencies above 330 Hz. Switching noise is eliminated by using a 680 k Ω resistor across the 0.047 µF. R3, R4 and C6 can be eliminated if enhanced stereo is not desired. As shown in Table 1, enhanced stereo and loudness are controlled through the same address. It is important to re- member to set both functions to the correct value any time either of these functions is updated. SERIAL DATA COMMUNICATION The LMC1982 uses the INTERMETAL serial bus (IM Bus) standard. Serial data information is sent to the LMC1982 over a three wire IM Bus consisting of Clock (CLK), Data (DATA), and Identity (ID). The DATA line is bidirectional and the CLK and ID lines are unidirectional from the micropro- cessor or micontroller to the LMC1982. The LMC1982’s bidi- rectional capability is accomplished by using an open drain output on the DATA line and an external 1 k Ω pull-up resistor. The LMC1982 responds to address values from 01000000 (40 H) through 01000111 (47H). The addresses select one of the eight available functions (see Table 1). The IM Bus’ lines have a logic high standby state when using TTL logic levels. As shown in Figure 7, data transmission is initiated by low levels on CLK and ID. Next, eight address bits are sent. This address information includes the code to select one of the LMC1982’s desired functions. Each address bit is clocked in on the rising edge of CLK. The ID line is taken high after the eight bits of address data are received by the LMC1982. The controlling system continues toggling the CLK line eight more times. Data that determines the selected function’s op- erating point is written into, or single bit information on DIGI- TAL INPUT 1 or DIGITAL INPUT 2 is read from, the LMC1982. Finally, the end of transmission is signalled by pulsing the ID line low for a minimum of 1 µs. The transmit- ted function data is latched and the function changes to its new setting. Table 1 also details the serial data structure, range, and bit assignments that sets each function’s operating point. The volume and tone controls’ function control data binarily incre- ments from zero to maximum as the function’s operating point changes from 80 dB attenuation to 0 dB attenuation (volume) or −12 dB to +12 dB (tone controls). Note that not all data bits are needed by each function. The extra bits shown as “X”s (“don’t cares”) are position holders and have no affect on a respective function. They are necessary to properly position the data in the LMC1982’s internal data shift register. Unexpected results may take place if these bits are not sent. The LMC1982’s internal data shift register can handle either a 16-bit word or two 8-bit serial data transmissions. It is the final 8 bits of data received before the ID line goes high that are used as the LMC1982 selection and function addresses. The final eight bits after the ID line returns high are used to change a function’s operating point. CLK must be stopped when the final 8 data bits are received. The data stored in the internal data latch remains unchanged until the ID is pulsed, signifying the end of data transmission. When ID is pulsed, the new data in the data shift register is latched into the data latch and the selected function takes on a new operating point. A complete description and more information concerning the IM Bus is given in the appendix of ITT’s CCU2000 datasheet. DIGITAL I/O The LMC1982’s two Digital Input pins, 2 and 3, provide single-bit communication between a peripheral device and the controller over the IM Bus. Each pin has an internal 30 k Ω pull-up resistor. Therefore, these pins should be con- nected to open collector/drain outputs. The type of informa- tion that could be received on these lines and retrieved by a controller include FM stereo pilot indication, power on/off, Secondary Audio Program (SAP), etc. According to Table 1, the logic state of DIGITAL INPUT 1 and DIGITAL INPUT 2 is latched and can be retrieved over the IM Bus using the read command (47 H). The single-bit informa- tion sent on the IM Bus is active low since these lines are in- ternally pulled high. DS011028-9 FIGURE 5. Loudness Control Circuit DS011028-10 FIGURE 6. Enhanced Stereo Circuit www.national.com 11 |
Similar Part No. - LMC1982CIN |
|
Similar Description - LMC1982CIN |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
