Electronic Components Datasheet Search |
|
P1610000 Datasheet(PDF) 10 Page - Red Lion Controls. Inc |
|
P1610000 Datasheet(HTML) 10 Page - Red Lion Controls. Inc |
10 / 28 page 10 7.0 progrAmming: ConFigurAtion loop 2-OP 1-IN 3-LC 4-AL 5-O2 9-FS no CNFP LOOP HIDDEN DISPLAY LOOP PARAMETERS INPUT MODULE MODULE OUTPUT PARAMETERS LOCKOUT PARAMETERS MODULE COOLING PARAMETERS MODULE FACTORY SERVICE MODULE ALARM PARAMETERS MODULE CONFIGURATION LOOP FRONT DISPLAY ENDS AND RETURNS TO START OF DISPLAY LOOP. RETURNS TO DISPLAY LOOP. ADVANCES TO NEXT MODULE. 240 °F CNFP TOP DISPLAY TEMP/PROCESS BOTTOM DISPLAY CNFP/MODULE 1-IN ENTERS MODULE OR AT CNFP/NO F1 To access the Configuration Loop, press the up key when F/ is displayed in the Hidden Loop. The arrow keys are used to select the parameter module (1-9). To enter a specific module press A while the module number is displayed. In the Configuration Loop, F will alternate with the parameter number in the bottom display. The Temperature/Process Value is shown in the top display. After entering a parameter module, press A to advance through the parameter names in the module. To change a parameter’s selection/value, press the arrow keys while the parameter is displayed. In the modules, the top display shows the parameter name, and the bottom display shows the selection/value. Use A to enter any selection/values that have been changed. The change is not committed to permanent memory until the controller is returned to the Display Loop. If a power loss occurs before returning to the Display Loop, the new values must be entered again. At the end of each module, the controller returns to F/. At this location, pressing A again returns the display to the the Display Loop. Pressing the Up key allows re-entrance to the Configuration Loop. Whenever L is pressed, n momentarily appears as the parameters are stored to permanent memory and the controller returns to the Display Loop. FRONT DISPLAY F1 ENDS AND RETURNS TO START AT RETURNS TO DISPLAY LOOP. ADVANCES SELECTION/VALUE. tYPE tc-j TOP DISPLAY PARAMETER BOTTOM DISPLAY SELECTION/VALUE ADVANCES TO NEXT PARAMETER OR OF DISPLAY LOOP. CNFP/NO 12 ALARMS RESET 12 With alarm models, the alarms can be manually reset. The up key resets Alarm 1 and the down key resets Alarm 2. ACCESS CODE 1 to 12 If the Access Code is set from -1 to -125, in Lockout Module , Access Code will appear here. By entering the proper Code, access to the Configuration Loop is permitted (with a negative Code value, the Hidden Loop can be accessed without the use of a code). With the factory setting of 0 or with an active User Input configured for Program Lock (), Access Code will not appear here. An active user input configured for Program Lock () always locks out the Configuration Loop, regardless of Access Code. AUTO-TUNE START The Auto-Tune procedure of the controller sets the Proportional Band, Integral Time, Derivative Time, Digital Filter, Control Output Dampening Time, and Relative Gain (Heat/Cool) values appropriate to the characteristics of the process. This parameter allows front panel starting or stopping of Auto-Tune. For more information, see PID Tuning Explanations. |
Similar Part No. - P1610000 |
|
Similar Description - P1610000 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |