Electronic Components Datasheet Search |
|
AC01-CS Datasheet(PDF) 7 Page - Vishay Siliconix |
|
AC01-CS Datasheet(HTML) 7 Page - Vishay Siliconix |
7 / 9 page AC01-CS, AC03-CS, AC05-CS www.vishay.com Vishay Draloric Revision: 12-Jul-16 7 Document Number: 28909 For technical questions, contact: ww1resistors@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TESTS PROCEDURES AND REQUIREMENTS All tests are carried out in accordance with the following specifications: • IEC 60115-1, generic specification (includes tests) The test and requirements table contains only the most important tests. For the full test schedule refer to the documents above. The tests are carried out in accordance with IEC 60068-2-xx test method and under standard atmospheric conditions in accordance with IEC 60068-1, 5.3. Climatic category -40 / 200 / 56 (rated temperature range: lower category temperature, upper category temperature; damp heat, steady state, test duration: 56 days) is valid. Unless otherwise specified the following values apply: • Temperature: 15 °C to 35 °C • Relative humidity: 45 % to 75 % • Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar) For performing some of the tests, the components are mounted on a test board in accordance with IEC 60115-1, 4.31. In test table below, only the relevant and commonly referred tests and related clauses of IEC 60115-1 and IEC 60068-2-xx test methods are mentioned. TEST PROCEDURES AND REQUIREMENTS IEC 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE ( R MAX.) 4.13 - Short time overload Room temperature; 10x rated power P40; 5 s ± (2 % R + 0.1 ) 4.16 21 (Ua1) 21 (Ub) 21 (Uc) Robustness of terminations Tensile, bending and torsion No damage ± (0.5 % R + 0.05 ) 4.18 20 (Tb) Resistance to soldering heat Unmounted components (260 ± 5) °C; (10 ± 1) s ± (0.5 % R + 0.05 ) 4.23 Climatic sequence: 4.23.2 2 (Ba) Dry heat 16 h; 200 °C ± (1 % R + 0.05 ) 4.23.3 30 (Db) Damp heat (accelerated) 1st cycle 24 h; 55 °C; 90 % to 100 % RH 4.23.4 1 (Aa) Cold 2 h; -55 °C 4.23.5 13 (M) Low air pressure 2 h; 8.5 kPa; 15 °C to 35 °C 4.23.6 30 (Db) Damp heat remaining cyclic 5 days; 55 °C; 95 % to 100 % RH; 5 cycles 4.24 78 (Cab) Damp heat, (steady state) 56 days; (40 ± 2) °C; (93 ± 5) % RH ± (5 % R + 0.1 ) 4.25.2 - Endurance (at room temperature) 1000 h; loaded with 116 % of P70; 1.5 h ON and 0.5 h OFF ± (5 % R + 0.1 ) 4.25.3 - Endurance (at 200 °C) 1000 h; without load ± (5 % R + 0.1 ) -- 1.2 / 50 μs surge test as defined in IEC 61000-4-5 (up to 6 kV) Internal impedance of surge tester is 2 ; 10 pulses at 30 s interval ± (5 % R + 0.1 ) -- Fail safe mains fusing at 230 VAC - Resistance > 100 k , fusing time < 2 s (fusing without flame and explosion) |
Similar Part No. - AC01-CS |
|
Similar Description - AC01-CS |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |