Electronic Components Datasheet Search |
|
PDI1394P23 Datasheet(PDF) 10 Page - NXP Semiconductors |
|
PDI1394P23 Datasheet(HTML) 10 Page - NXP Semiconductors |
10 / 42 page Philips Semiconductors Preliminary data PDI1394P23 2-port/1-port 400 Mbps physical layer interface 2001 Sep 06 10 The LPS input is considered inactive if it remains low for more than 2.6 µs and is considered active otherwise. When the PDI1394P23 detects that LPS is inactive, it will place the PHY-LLC interface into a low-power reset state in which the CTL and D outputs are held in the logic zero state and the LREQ input is ignored; however, the SYSCLK output remains active. If the LPS input remains low for more than 26 µs, the PHY–LLC interface is put into a low-power disabled state in which the SYSCLK output is also held inactive. The PHY-LLC interface is also held in the disabled state during hardware reset. The PDI1394P23 will continue the necessary repeater functions required for normal network operation regardless of the state of the PHY-LLC interface. When the interface is in the reset or disabled state and LPS is again observed active, the PHY will initialize the interface and return it to normal operation. The PHY uses the C/LKON terminal to notify the LLC to power up and become active. When activated, the C/LKON signal is a square wave of approximately 163 ns period. The PHY activates the C/LKON output when the LLC is inactive and a wake-up event occurs. The LLC is considered inactive when either the LPS input is inactive, as described above, or the LCtrI bit is cleared to 0. A wake-up event occurs when a link-on PHY packet addressed to this node is received, or conditionally when a PHY interrupt occurs. The PHY deasserts the C/LKON output when the LLC becomes active (both LPS active and the LCtrl bit set to 1). The PHY also deasserts the C/LKON output when a bus-reset occurs unless a PHY interrupt condition exists which would otherwise cause C/LKON to be active. 8.0 ABSOLUTE MAXIMUM RATINGS 1 In accordance with the Absolute Maximum Rating System (IEC 134). Voltages are referenced to GND (ground = 0 V). SYMBOL PARAMETER CONDITION LIMITS UNIT SYMBOL PARAMETER CONDITION MIN MAX UNIT VDD DC supply voltage –0.5 4.0 V VI DC input voltage –0.5 VDD+0.5 V VI–5V 5 volt tolerant input voltage range –0.5 5.5 V VO DC output voltage range at any output –0.5 VDD+0.5 V Electrostatic discharge Human Body Model — 2 kV Electrostatic discharge Machine Model — 200 V Tamb Operating free-air temperature range 0 +70 °C Tstg Storage temperature range –65 +150 °C NOTE: 1. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “Recommended Operating Conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. |
Similar Part No. - PDI1394P23 |
|
Similar Description - PDI1394P23 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |