M95256-RMN3G datasheet(6/39 Pages) STMICROELECTRONICS

Part #	M95256-RMN3G

Description	256Kbit and 128Kbit Serial SPI Bus EEPROM With High Speed Clock

Download	39 Pages

Scroll/Zoom	100%

Manufacturer	STMICROELECTRONICS [STMicroelectronics]

Direct Link	http://www.st.com

Logo

6 / 39 page

M95256, M95128

6/39

SIGNAL DESCRIPTION

During all operations, VCC must be held stable and

within the specified valid range: VCC(min) to

VCC(max).

All of the input and output signals must be held

High or Low (according to voltages of VIH, VOH, VIL

or VOL, as specified in Table 13. to Table 17.).

These signals are described next.

Serial Data Output (Q). This

output

signal is

used to transfer data serially out of the device.

Data is shifted out on the falling edge of Serial

Clock (C).

Serial Data Input (D). This input signal is used to

transfer data serially into the device. It receives in-

structions, addresses, and the data to be written.

Values are latched on the rising edge of Serial

Clock (C).

Serial Clock (C). This input signal provides the

timing of the serial interface. Instructions, address-

es, or data present at Serial Data Input (D) are

latched on the rising edge of Serial Clock (C). Data

on Serial Data Output (Q) changes after the falling

edge of Serial Clock (C).

Chip Select (S). When this input signal is High,

the device is deselected and Serial Data Output

(Q) is at high impedance. Unless an internal Write

cycle is in progress, the device will be in the Stand-

by Power mode. Driving Chip Select (S) Low se-

lects the device, placing it in the Active Power

mode.

After Power-up, a falling edge on Chip Select (S)

is required prior to the start of any instruction.

Hold (HOLD). The Hold (HOLD) signal is used to

pause any serial communications with the device

without deselecting the device.

During the Hold condition, the Serial Data Output

(Q) is high impedance, and Serial Data Input (D)

and Serial Clock (C) are Don’t Care.

To start the Hold condition, the device must be se-

lected, with Chip Select (S) driven Low.

Write Protect (W). The main purpose of this in-

put signal is to freeze the size of the area of mem-

ory that is protected against Write instructions (as

specified by the values in the BP1 and BP0 bits of

the Status Register).

This pin must be driven either High or Low, and

must be stable during all write instructions.

Similar Part No. - M95256-RMN3G

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	M95256-RMN3G/A	345Kb / 39P	256 Kbit Serial SPI bus EEPROM with high speed clock
	M95256-RMN3G/A	504Kb / 48P	256 Kbit serial SPI bus EEPROM with high-speed clock
	M95256-RMN3G/K	504Kb / 48P	256 Kbit serial SPI bus EEPROM with high-speed clock
	M95256-RMN3G/V	345Kb / 39P	256 Kbit Serial SPI bus EEPROM with high speed clock

More results

Similar Description - M95256-RMN3G

Manufacturer	Part #	Datasheet	Description
Sanyo Semicon Device	LE25LB1282TT	256Kb / 14P	Serial SPI EEPROM (SPI Bus)(128Kbit)
	LE25CB1282M	297Kb / 13P	Serial SPI EEPROM (SPI Bus)(128Kbit)
	LE25LB2562M	254Kb / 14P	256Kbit Serial SPI EEPROM (SPI Bus)
Asahi Kasei Microsystem...	AK6516C	129Kb / 17P	SPI bus 256Kbit Serial CMOS EEPROM
STMicroelectronics	M24256-BW	454Kb / 25P	256Kbit and 128Kbit Serial I2C Bus EEPROM With Three Chip Enable Lines
	M95512-W	531Kb / 31P	512Kbit Serial SPI Bus EEPROM With High Speed Clock June 2005
	M95512	195Kb / 31P	512Kbit Serial SPI Bus EEPROM With High Speed Clock
	M95080	648Kb / 40P	16Kbit and 8Kbit Serial SPI Bus EEPROM With High Speed Clock
Sanyo Semicon Device	LE25LB2562M	319Kb / 14P	256Kbit Serial SPI EEPROM
STMicroelectronics	M95640	590Kb / 39P	64Kbit and 32Kbit Serial SPI Bus EEPROM With High Speed Clock November 2003

More results

M95256-RMN3G Datasheet(PDF) 6 Page - STMicroelectronics

M95256-RMN3G Datasheet(HTML) 6 Page - STMicroelectronics

Similar Part No. - M95256-RMN3G

Similar Description - M95256-RMN3G

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39

Datasheet Download

Link URL