TS5A3357

SINGLE 5 W SP3T ANALOG SWITCH

5V/3.3V 3:1 ANALOG MULTIPLEXER/DEMULTIPLEXER

SCDS177 – OCTOBER 2004

www.ti.com

5

Electrical Characteristics for 3.3 V Supply

PARAMETER

SYMBOL

TEST CONDITIONS

TA

V+

MIN

TYP(1)

MAX

UNIT

ANALOG SWITCH

Analog Signal Range

VCOM,VNO

0

V+

V

Peak On-Resistance

rpeak

0

≤ VNO ≤ V+, ICOM = −24 mA,

Switch ON,

see Figure 12

Full

3 V

25

Ω

VNO = 0 V, ICOM = 24 mA

25

°C

6.5

9

On-Resistance

ron

VNO = 0 V, ICOM = 24 mA

Switch ON,

Full

3 V

9

Ω

On-Resistance

ron

VNO = 3 V, ICOM = −24 mA

Switch ON,

see Figure 12

25

°C

3 V

9

20

Ω

VNO = 3 V, ICOM = −24 mA

Full

20

On-Resistance

match between

channels

∆ron

VNO = 2.1 V,

ICOM = −24 mA,

Switch ON,

see Figure 12

25

°C

3 V

0.1

Ω

On-Resistance

flatness

ron(flat)

0

≤ VNO ≤ V+,

ICOM = −24 mA,

Switch ON,

see Figure 12

25

°C

3.3 V

13.5

Ω

NO Off-Leakage

INO(OFF)

VNO = 0 to V+, VCOM = V+ to 0,

Switch OFF,

25

°C

3.6 V

−0.1

0.1

A

NO Off-Leakage

Current

INO(OFF)

VNO = 0 to V+, VCOM = V+ to 0,

Switch OFF,

see Figure 13

Full

3.6 V

−1

1

µA

COM Off-Leakage

ICOM(OFF) VNO = 0 to V+, VCOM = V+ to 0,

Switch OFF,

25

°C

3.6 V

−0.1

0.1

A

COM Off-Leakage

Current

ICOM(OFF) VNO = 0 to V+, VCOM = V+ to 0,

Switch OFF,

see Figure 13

Full

3.6 V

−1

1

µA

NO On-Leakage

INO(ON)

VNO = 0 to V+, VCOM = Open,

Switch ON,

25

°C

3.6 V

−0.1

0.1

A

NO On-Leakage

Current

INO(ON)

VNO = 0 to V+, VCOM = Open,

Switch ON,

see Figure 13

Full

3.6 V

−1

1

µA

COM On-Leakage

ICOM(ON)

VNO = Open, VCOM = 0 to V+,

Switch ON,

25

°C

3.6 V

−0.1

0.1

A

COM On-Leakage

Current

ICOM(ON)

VNO = Open, VCOM = 0 to V+,

Switch ON,

see Figure 13

Full

3.6 V

−1

1

µA

DIGITAL INPUTS (IN1, IN2)(2)

Input Logic High

VIH

Full

0.7

× V+

5.5

V

Input Logic Low

VIL

Full

0

0.3

× V+

V

Input Leakage

IIH, IIL

VIN = 5.5 V or 0

25

°C

3.6 V

−1

0.1

µA

Input Leakage

Current

IIH, IIL

VIN = 5.5 V or 0

Full

3.6 V

1

µA

(1) All typical values are at V+ = 3.3 V, TA = 25°C.

(2) All unused digital inputs of the device must be held at V+ or GND to ensure proper device operation. Refer to the TI application report, Implications

of Slow or Floating CMOS Inputs, literature number SCBA004.