![]() |
Electronic Components Datasheet Search |
|
EM78P447NAM Datasheet(PDF) 19 Page - ELAN Microelectronics Corp |
|
EM78P447NAM Datasheet(HTML) 19 Page - ELAN Microelectronics Corp |
19 / 57 page ![]() EM78P447N OTP ROM The above two cases will cause the controller EM78P447N to reset. The T and P flags of R3 can be used to determine the source of the reset (wake-up). In addition to the basic SLEEP1 MODE, EM78P447N has another sleep mode (designated as SLEEP2 MODE and is invoked by clearing the IOCE register “SLPC” bit). In the SLEEP2 MODE, the controller can be awakened by- (A) Any of the wake-up pins is “0” as illustrated in Figure. 5. Upon waking, the controller will continue to execute the succeeding address. Under this case, before entering SLEEP2 MODE, the wake-up function of the trigger sources (P60~P67 and P74~P75) should be selected (e.g., input pin) and enabled (e.g., pull-high, wake-up control). It should be noted that after waking up, the WDT is enabled if the Code Option bit ENWDT is “0”. The WDT operation (to be enabled or disabled) should be appropriately controlled by software after waking up. (B) WDT time-out (if enabled) or external reset input on /RESET pin will trigger a controller reset. Table 4 Usage of Sleep1 and Sleep2 Mode Usage of Sleep1 and Sleep2 Mode SLEEP2 SLEEP1 (a) Before SLEEP (a) Before SLEEP 1. Set Port6 or P74 or P75 Input 1. Execute SLEP instruction 2. Enable Pull-High and set WDT prescaler over 1:1 (Set CONT.7 and CONT.3 ~ CONT.0) 3. Enable Wake-up (Set IOCB or IOCE.0) 4. Execute Seep2 (Set IOCE.4) (b) After Wake-up (b) After Wake-up 1. Next instruction 1. Reset 2. Disable Wake-up 3. Disable WDT (Set IOCE.5) If Port6 Input Status Changed Wake-up is used to wake-up the EM78P447S (Case [a] above), the following instructions must be executed before entering SLEEP2 mode: This specification is subject to change without prior notice. 10.21.2004 (V1.0) 19 MOV A, @11111111b ; Set Port6 input IOW R6 MOV A, @0xxx1010b ; Set Port6 pull-high, WDT prescaler, prescaler must set over 1:1 CONTW MOV A, @00000000b ; Enable Port6 wake-up function IOW RB MOV A, @xx00xxx1b ; Enable SLEEP2 IOW RE After Wake-up NOP MOV A, @11111111b ; Disable Port6 wake-up function |
Similar Part No. - EM78P447NAM |
|
Similar Description - EM78P447NAM |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |
allmanual.com |