Electronic Components Datasheet Search |
|
IS25C04-3GLA3 Datasheet(PDF) 6 Page - Integrated Silicon Solution, Inc |
|
IS25C04-3GLA3 Datasheet(HTML) 6 Page - Integrated Silicon Solution, Inc |
6 / 17 page 6 Integrated Silicon Solution, Inc. — 1-800-379-4774 Preliminary Information Rev. 00F 12/22/05 IS25C02 IS25C04 ISSI® Table 5. Address Key Name IS25C02 IS25C04 A N A 7-A0 A 8-A0 Don't A 8 - Care Bits WRITE STATUS REGISTER (WRSR) This instruction lets the user choose a Block Protection setting. The values of the other data bits incorporated into WRSR can be 0 or 1, and are not stored in the Status Register. WRSR will be ignored unless both the following are true: a) WEN = 1, due to a prior WREN instruction; and b) Hardware Write Protection is not enabled. (See Table 4 for details). Except for the RDY status, the values in the Status Register remain un- changed until the moment when the write cycle is complete and the register is updated. Once successfully completed, WEN is reset for complete chip write protec- tion. (See Figure 5 for timing). READ DATA (READ) This instruction begins with the op-code and the 8-bit address, and causes the selected data byte to be shifted out on SO. Following this first data byte, addi- tional sequential bytes are output. If the data byte in the highest address is output, the address rolls-over to the lowest address in the array, and the output could loop indefinitely. At any time, a rising CS signal completes the operation. (See Figure 6 for timing). WRITE DATA (WRITE) The WRITE instruction begins with the op-code, the 8-bit address of the first byte to be modified, and the first data byte. Additional data bytes may be written sequentially to the array after the first byte. Each WRITE instruction can affect the contents of a 16 byte page, but no more. The page begins at address XXXX 0000, and ends with XXXX 1111. If the last byte of the page is input, the address rolls over to the beginning of the same page. More than 16 data bytes can be input during the same instruction, but upon a completed write cycle, a page would only contain the last 16 bytes. The region of the array defined within Block Protection cannot be modified as long as that block configuration is selected. The region of the array outside the Block Protection can only be modified if Write Enable (WEN) is set to 1. Therefore, it may be necessary that a WREN instruction occur prior to WRITE. In addition, if Hardware Write Protection is enabled, the memory array cannot be modified. Once Write is successfully completed, WEN is reset for complete chip write protection. (See Figure 7 for timing). Table 4. Write Protection WP WP WP WP WP Hardware Write WEN Inside Block Outside Block Status Register Protection 0 Enabled X Read-only Read-only Read-only 1 Not Enabled 0 Read-only Read-only Read-only 1 Not Enabled 1 Read-only Unprotected Unprotected Note: X = Don't care bit. |
Similar Part No. - IS25C04-3GLA3 |
|
Similar Description - IS25C04-3GLA3 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |