 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
X9251TS24I Datasheet(PDF) 5 Page - Intersil Corporation |
|
||||||||||||||||||||||||||||||
X9251TS24I Datasheet(HTML) 5 Page - Intersil Corporation |
|
|
5 / 20 page  5 FN8166.5 April 13, 2007 One of Four Potentiometers Power Up and Down Recommendations There are no restrictions on the power-up or power-down conditions of VCC and the voltages applied to the potentiometer pins provided that VCC is always more positive than or equal to VH, VL, and VW (i.e., VCC ≥ VH, VL, VW). The VCC ramp rate specification is always in effect. Wiper Counter Register (WCR) The X9251 contains four Wiper Counter Registers, one for each potentiometer. The Wiper Counter Register can be envisioned as a 8-bit parallel and serial load counter with its outputs decoded to select one of 256 wiper positions along its resistor array. The contents of the WCR can be altered in four ways: it may be written directly by the host via the Write Wiper Counter Register instruction (serial load); it may be written indirectly by transferring the contents of one of four associated data registers via the XFR Data Register instruction (parallel load); it can be modified one step at a time by the Increment/Decrement instruction (See Instruction section for more details). Finally, it is loaded with the contents of its Data Register zero (DR#0) upon power-up. (See Figure 1) The wiper counter register is a volatile register; that is, its contents are lost when the X9251 is powered-down. Although the register is automatically loaded with the value in DR#0 upon power-up, this may be different from the value present at power-down. Power-up guidelines are recommended to ensure proper loadings of the DR#0 value into the WCR#. Data Registers (DR) Each of the four DCPs has four 8-bit non-volatile Data Registers. These can be read or written directly by the host. Data can also be transferred between any of the four Data Registers and the associated Wiper Counter Register. All operations changing data in one of the Data Registers is a non-volatile operation and takes a maximum of 10ms. If the application does not require storage of multiple settings for the potentiometer, the Data Registers can be used as regular memory locations for system parameters or user preference data. Bits [7:0] are used to store one of the 256 wiper positions or data (0 ~ 255). Status Register (SR) This 1-bit Status Register is used to store the system status. WIP: Write In Progress status bit, read only. • When WIP = 1, indicates that high-voltage write cycle is in progress. • When WIP = 0, indicates that no high-voltage write cycle is in progress. SERIAL DATA PATH FROM INTERFACE CIRCUITRY DR#0 SERIAL BUS INPUT PARALLEL BUS INPUT COUNTER REGISTER INC/DEC LOGIC UP/DN CLK MODIFIED SCK UP/DN 8 8 COUNTER IF WCR = 00[H] then RW is closet to RL IF WCR = FF[H] then RW is closet to RH WIPER (WCR#) #: 0, 1, 2, or 3 DR#2 DR#1 DR#3 - - - DECODE DCP CORE RW RH RL FIGURE 1. DETAILED POTENTIOMETER BLOCK DIAGRAM X9251 |
Similar Part No. - X9251TS24I |
|
Similar Description - X9251TS24I |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
