![]() |
Electronic Components Datasheet Search |
|
ENC28J60 Datasheet(PDF) 6 Page - Microchip Technology |
|
ENC28J60 Datasheet(HTML) 6 Page - Microchip Technology |
6 / 96 page ![]() ENC28J60 DS39662B-page 4 Preliminary © 2006 Microchip Technology Inc. FIGURE 1-2: TYPICAL ENC28J60-BASED INTERFACE TABLE 1-1: PINOUT I/O DESCRIPTIONS Pin Name Pin Number Pin Type Buffer Type Description SPDIP, SOIC, SSOP QFN VCAP 1 25 P — 2.5V output from internal regulator. A low Equivalent Series Resistance (ESR) capacitor, with a typical value of 10 μF and a minimum value of 1 μF to ground, must be placed on this pin. VSS 2 26 P — Ground reference. CLKOUT 3 27 O — Programmable clock output pin.(1) INT 4 28 O — INT interrupt output pin.(2) NC 5 1 O — Reserved function; always leave unconnected. SO 6 2 O — Data out pin for SPI interface.(2) SI 7 3 I ST Data in pin for SPI interface.(3) SCK 8 4 I ST Clock in pin for SPI interface.(3) CS 9 5 I ST Chip select input pin for SPI interface.(3,4) RESET 10 6 I ST Active-low device Reset input.(3, 4) VSSRX 11 7 P — Ground reference for PHY RX. TPIN- 12 8 I ANA Differential signal input. TPIN+ 13 9 I ANA Differential signal input. RBIAS 14 10 I ANA Bias current pin for PHY. Must be tied to ground via a resistor (refer to Section 2.4 “Magnetics, Termination and Other External Components” for details). VDDTX 15 11 P — Positive supply for PHY TX. TPOUT- 16 12 O — Differential signal output. TPOUT+ 17 13 O — Differential signal output. VSSTX 18 14 P — Ground reference for PHY TX. VDDRX 19 15 P — Positive 3.3V supply for PHY RX. VDDPLL 20 16 P — Positive 3.3V supply for PHY PLL. VSSPLL 21 17 P — Ground reference for PHY PLL. VSSOSC 22 18 P — Ground reference for oscillator. OSC1 23 19 I ANA Oscillator input. OSC2 24 20 O — Oscillator output. VDDOSC 25 21 P — Positive 3.3V supply for oscillator. LEDB 26 22 O — LEDB driver pin.(5) LEDA 27 23 O — LEDA driver pin.(5) VDD 28 24 P — Positive 3.3V supply. Legend: I = Input, O = Output, P = Power, DIG = Digital input, ANA = Analog signal input, ST = Schmitt Trigger Note 1: Pins have a maximum current capacity of 8 mA. 2: Pins have a maximum current capacity of 4 mA. 3: Pins are 5V tolerant. 4: Pins have an internal weak pull-up to VDD. 5: Pins have a maximum current capacity of 12 mA. TRANSFORMER MCU TX/RX Buffer MAC PHY LEDA LEDB SI SO SCK INT SDO SDI SCK INTX ENC28J60 TPIN+/- TPOUT+/- ETHERNET RJ45 I/O CS |
Similar Part No. - ENC28J60_06 |
|
Similar Description - ENC28J60_06 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |
allmanual.com |