5962-9957001Q2A datasheet(4/41 Pages) TI

Part #	5962-9957001Q2A

Description	3-V TO 5.5-V, 12-BIT, 200-KSPS, 4-/8-CHANNEL, LOW-POWER SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER-DOWN

Download	41 Pages

Scroll/Zoom	100%

Manufacturer	TI [Texas Instruments]

Direct Link	http://www.ti.com

Logo

4 / 41 page

TLV2544Q, TLV2548Q, TLV2548M

3-V TO 5.5-V, 12-BIT, 200-KSPS, 4-/8-CHANNEL, LOW-POWER

SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER-DOWN

SGLS119C – FEBRUARY 2002 – REVISED OCTOBER 2002

4

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

Terminal Functions (Continued)

TERMINAL

NAME

NO.

I/O

DESCRIPTION

NAME

TLV2544

TLV2548

SDO

1

O

The 3-state serial output for the A/D conversion result. SDO is kept in the high-impedance state

when CS is high and after the CS falling edge and until the MSB (D15) is presented. The output

format is MSB (D15) first.

When FS is not used (FS = 1 at the falling edge of CS), the MSB (D15) is presented to the SDO pin

after the CS falling edge, and successive data are available at the rising edge of SCLK.

When FS is used (FS = 0 at the falling edge of CS), the MSB (D15) is presented to SDO after the

falling edge of CS and FS = 0 is detected. Successive data are available at the falling edge of SCLK.

(This is typically used with an active FS from a DSP.)

For conversion and FIFO read cycles, the first 12 bits are result from previous conversion (data)

followed by 4 don’t care bits. The first four bits from SDO for CFR read cycles should be ignored.

The register content is in the last 12 bits. SDO is 3-state (float) after the 16th bit.

REFM

14

18

I

External reference input or internal reference decoupling.

REFP

15

19

I

External reference input or internal reference decoupling. (Shunt capacitors of 10

µF and 0.1 µF

between REFP and REFM.) The maximum input voltage range is determined by the difference

between the voltage applied to this terminal and the REFM terminal when an external reference is

used.

VCC

5

I

Positive supply voltage

detailed description

analog inputs and internal test voltages

The 4/8 analog inputs and three internal test inputs are selected by the analog multiplexer depending on the

command entered. The input multiplexer is a break-before-make type to reduce input-to-input noise injection

resulting from channel switching.

converter

The TLV2544/48 uses a 12-bit successive approximation ADC utilizing a charge redistribution DAC. Figure 1

shows a simplified version of the ADC.

The sampling capacitor acquires the signal on Ain during the sampling period. When the conversion process

starts, the SAR control logic and charge redistribution DAC are used to add and subtract fixed amounts of charge

from the sampling capacitor to bring the comparator into a balanced condition. When the comparator is

balanced, the conversion is complete and the ADC output code is generated.

Charge

Redistribution

DAC

Control

Logic

_

+

REFM

Ain

ADC Code

Figure 1. Simplified Model of the Successive-Approximation System

Similar Part No. - 5962-9957001Q2A

Manufacturer	Part #	Datasheet	Description
Texas Instruments	5962-9957601Q2A	679Kb / 23P	[Old version datasheet] 2.7-V TO 5.5-V LOW-POWER DUAL 12-BIT DIGITAL-TO-ANALOG CONVERTER WITH INTERNAL REFERENCE AND POWER DOWN
	5962-9957601Q2A	906Kb / 24P	[Old version datasheet] 2.7-V TO 5.5-V LOW-POWER DUAL 12-BIT DIGITAL-TO-ANALOG CONVERTER WITH INTERNAL REFERENCE AND POWER DOWN
	5962-9957601QPA	679Kb / 23P	[Old version datasheet] 2.7-V TO 5.5-V LOW-POWER DUAL 12-BIT DIGITAL-TO-ANALOG CONVERTER WITH INTERNAL REFERENCE AND POWER DOWN
	5962-9957601QPA	906Kb / 24P	[Old version datasheet] 2.7-V TO 5.5-V LOW-POWER DUAL 12-BIT DIGITAL-TO-ANALOG CONVERTER WITH INTERNAL REFERENCE AND POWER DOWN

More results

Similar Description - 5962-9957001Q2A

Manufacturer	Part #	Datasheet	Description
Texas Instruments	TLV2544Q	623Kb / 37P	[Old version datasheet] 3-V TO 5.5-V, 12-BIT, 200-KSPS, 4-/8-CHANNEL, LOW-POWER SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER-DOWN
	TLV2541	426Kb / 26P	[Old version datasheet] 2.7 V TO 5.5 V, LOW POWER, 12-BIT, 200 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
	TLV2541IDR	1Mb / 30P	[Old version datasheet] 2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
	TLV2541	1Mb / 33P	[Old version datasheet] 2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
	TLV2542IDR	1Mb / 31P	[Old version datasheet] 2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
	TLV2548-EP	1Mb / 38P	[Old version datasheet] 3.0-V TO 5.5-V, 12-BIT, 200-KSPS, 4-/8-CHANNEL, LOW-POWER SERIAL ANALOG-TO-DIGITAL CONVERTER WITH AUTOPOWER-DOWN
	TLV2544	648Kb / 39P	[Old version datasheet] 2.7 V TO 5.5 V, 12-BIT, 200 KSPS, 4/8 CHANNEL, LOW POWER, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTO POWER DOWN
	TLV2544	1Mb / 49P	[Old version datasheet] 2.7 V TO 5.5 V, 12-BIT, 200 KSPS, 4/8 CHANNEL, LOW POWER, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTO POWER DOWN
	TLC2551	365Kb / 23P	[Old version datasheet] 5 V, LOW POWER, 12-BIT, 400 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
	TLV1504	638Kb / 42P	[Old version datasheet] 2.7 V TO 5.5 V, 10-BIT, 200 KSPS, 4/8 CHANNEL, LOW POWER, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTO POWER DOWN

More results

5962-9957001Q2A Datasheet(PDF) 4 Page - Texas Instruments

5962-9957001Q2A Datasheet(HTML) 4 Page - Texas Instruments

Similar Part No. - 5962-9957001Q2A

Similar Description - 5962-9957001Q2A

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41

Datasheet Download

Link URL