LPC2292_07 datasheet(2/54 Pages) PHILIPS

Part #	LPC2292

Description	16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface

Download	54 Pages

Scroll/Zoom	100%

Manufacturer	PHILIPS [NXP Semiconductors]

Direct Link	http://www.nxp.com

Logo

2 / 54 page

LPC2292_2294_6

Product data sheet

Rev. 06 — 10 December 2007

2 of 54

NXP Semiconductors

LPC2292/LPC2294

16/32-bit ARM microcontrollers with external memory interface

I 16 kB on-chip static RAM and 256 kB on-chip ﬂash program memory. 128-bit wide

interface/accelerator enables high-speed 60 MHz operation.

I In-System Programming/In-Application Programming (ISP/IAP) via on-chip bootloader

software. Single ﬂash sector or full chip erase in 400 ms and programming of 256 B in

1 ms.

I EmbeddedICE-RT and Embedded Trace interfaces offer real-time debugging with the

on-chip RealMonitor software as well as high-speed real-time tracing of instruction

execution.

I Two/four (LPC2292/2294) interconnected CAN interfaces with advanced acceptance

ﬁlters. Additional serial interfaces include two UARTs (16C550), Fast I2C-bus

(400 kbit/s) and two SPIs.

I Eight channel 10-bit ADC with conversion time as low as 2.44 µs.

I Two 32-bit timers (with four capture and four compare channels), PWM unit (six

outputs), Real-Time Clock (RTC), and watchdog.

I Vectored Interrupt Controller (VIC) with conﬁgurable priorities and vector addresses.

I Conﬁgurable external memory interface with up to four banks, each up to 16 MB and

8/16/32-bit data width.

I Up to 112 general purpose I/O pins (5 V tolerant). Up to nine edge/level sensitive

external interrupt pins available.

I 60 MHz maximum CPU clock available from programmable on-chip PLL with settling

time of 100

µs.

I On-chip crystal oscillator with an operating range of 1 MHz to 30 MHz.

I Power saving modes include Idle and Power-down.

I Processor wake-up from Power-down mode via external interrupt.

I Individual enable/disable of peripheral functions for power optimization.

I Dual power supply:

N CPU operating voltage range of 1.65 V to 1.95 V (1.8 V ± 0.15 V).

N I/O power supply range of 3.0 V to 3.6 V (3.3 V ± 10 %) with 5 V tolerant I/O pads.

3.

Ordering information

Table 1.

Ordering information

Type number

Package

Name

Description

Version

LPC2292FBD144

LQFP144

plastic low proﬁle quad ﬂat package;

144 leads; body 20

× 20 × 1.4 mm

SOT486-1

LPC2292FBD144/00

LQFP144

plastic low proﬁle quad ﬂat package;

144 leads; body 20

× 20 × 1.4 mm

SOT486-1

LPC2292FBD144/01

LQFP144

plastic low proﬁle quad ﬂat package;

144 leads; body 20

× 20 × 1.4 mm

SOT486-1

LPC2292FET144/00

TFBGA144

plastic thin ﬁne-pitch ball grid array package;

144 balls; body 12

× 12 × 0.8 mm

SOT569-1

LPC2292FET144/01

TFBGA144

plastic thin ﬁne-pitch ball grid array package;

144 balls; body 12

× 12 × 0.8 mm

SOT569-1

LPC2292FET144/G

TFBGA144

plastic thin ﬁne-pitch ball grid array package;

144 balls; body 12

× 12 × 0.8 mm

SOT569-1

Similar Part No. - LPC2292_07

Manufacturer	Part #	Datasheet	Description
NXP Semiconductors	LPC2292FBD144	188Kb / 40P	16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface Rev. 01-05 February 2004
	LPC2292FBD144	279Kb / 53P	16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface Rev. 7-4 December 2008
	LPC2292FBD144/00	279Kb / 53P	16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface Rev. 7-4 December 2008
	LPC2292FBD144/01	279Kb / 53P	16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface Rev. 7-4 December 2008
	LPC2292FET144/00	279Kb / 53P	16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface Rev. 7-4 December 2008

More results

Similar Description - LPC2292_07

Manufacturer	Part #	Datasheet	Description
NXP Semiconductors	LPC2292	188Kb / 40P	16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface Rev. 01-05 February 2004
	LPC2292	456Kb / 54P	16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface Rev. 8-8 June 2011
	LPC2292	279Kb / 53P	16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface Rev. 7-4 December 2008
	LPC2212	208Kb / 45P	16/32-bit ARM microcontrollers; 128/256 kB ISP/IAP flash with 10-bit ADC and external memory interface Rev. 04-3 January 2008
	LPC2212	185Kb / 40P	16/32-bit ARM microcontrollers; 128/256 kB ISP/IAP Flash with 10-bit ADC and external memory interface Rev. 02-23 December 2004
	LPC2212	196Kb / 45P	16/32-bit ARM microcontrollers; 128/256 kB ISP/IAP flash with 10-bit ADC and external memory interface Rev. 04-3 January 2008
	LPC2212	359Kb / 47P	Single-chip 16/32-bit ARM microcontrollers; 128/256 kB ISP/IAP flash with 10-bit ADC and external memory interface Rev. 5-14 June 2011
	LPC2194	158Kb / 33P	Single-chip 16/32-bit microcontrollers 256 kB ISP/IAP Flash with 10-bit ADC and CAN Rev. 01-06 February 2004
	LPC2212	359Kb / 47P	Single-chip 16/32-bit ARM microcontrollers; 128/256 kB ISP/IAP flash with 10-bit ADC Rev. 5-14 June 2011
	LPC2119	163Kb / 34P	Single-chip 16/32-bit microcontrollers; 128/256 kB ISP/IAP Flash with 10-bit ADC and CAN Rev. 03-22 December 2004

More results

LPC2292 Datasheet(PDF) 2 Page - NXP Semiconductors

LPC2292 Datasheet(HTML) 2 Page - NXP Semiconductors

Similar Part No. - LPC2292_07

Similar Description - LPC2292_07

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

Datasheet Download

Link URL