8

All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.

Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality

Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without

notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and

reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result

from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.

For information regarding Intersil Corporation and its products, see www.intersil.com

Sales Office Headquarters

NORTH AMERICA

Intersil Corporation

7585 Irvine Center Drive

Suite 100

Irvine, CA 92618

TEL: (949) 341-7000

FAX: (949) 341-7123

Intersil Corporation

2401 Palm Bay Rd.

Palm Bay, FL 32905

TEL: (321) 724-7000

FAX: (321) 724-7946

EUROPE

Intersil Europe Sarl

Ave. William Graisse, 3

1006 Lausanne

Switzerland

TEL: +41 21 6140560

FAX: +41 21 6140579

ASIA

Intersil Corporation

Unit 1804 18/F Guangdong Water Building

83 Austin Road

TST, Kowloon Hong Kong

TEL: +852 2723 6339

FAX: +852 2730 1433

HCTS164MS

Spec Number

518613

Intersil Space Level Product Flow - MS

Wafer Lot Acceptance, All Lots (including SEM);

Method 5007

Gamma Radiation Verification, Each Wafer, 4 Samples/

Wafer, 0 Rejects, Method 1019

100% Nondestructive Bond Pull, Method 2023

Sample Wire Bond Pull Monitor, Method 2011

Sample Die Shear Monitor, Method 2019 or 2027

100% Internal Visual Inspection - Method 2010, Condition A

100% Temperature Cycling, Method 1010, Condition C,

10 Cycles

100% Constant Acceleration Method 2001, Condition per

Method 5004

100% PIND, Method 2020, Condition A

100% External Visual

100% Serialization

100% Initial Electrical Test (T0)

100% Static Burn-In 1, Method 1015, Condition A or B,

100% Interim Electrical Test (T1)

100% Delta Calculation (T0-T1)

100% Static Burn-In 2, Method 1015, Condition A or B, 24

100% Interim Electrical Test 2 (T2)

100% Delta Calculation (T0-T2)

100% PDA 1, Method 5004 (see Notes 1, 2)

Equivalent per Method 1015

100% Interim Electrical Test 3 (T3)

100% Delta Calculation (T0-T3)

100% PDA 2, Method 5004 (see Note 2)

100% Final Electrical Test

100% Fine/Gross Leak, Method 1014

100% Radiographic, Method 2012 (see Note 3)

100% External Visual, Method 2009

Sample Group A, Method 5005 (see Note 4)

100% Data Package Generation (see Note 5)

NOTES:

1. Failures from Interim Electrical Test 1 and 2 are combined for determining PDA 1.

2. Failures from subgroups 1, 7, 9 and deltas are used for calculating PDA. The maximum allowable PDA = 5% with no more than 3% of the

failures from subgroup 7.

3. Radiographic (X-Ray) inspection may be performed at any point after serialization as allowed by Method 5004.

4. Alternate Group A as allowed by MIL-STD-883, Method 5005 may be performed.

5. Data package contains:

• Cover Sheet (Intersil name and/or logo, PO #, customer part #, lot date code, Intersil part #, lot #, quantity).

• Wafer lot acceptance report (Method 5007). Includes reproductions of SEM photos with % step coverage. GAMMA Radiation Report. Con-

tains cover page, disposition, rad dose, Lot #, test package used, specifications #s, test equipment, etc. radiation read and record data on

file at Intersil.

• X- Ray report and film. Includes pentrameter measurements.

• Screening, electrical, and group A attributes (screening attributes begin after package seal).

• Lot serial number sheet (good units serial # and lot #).

• Variables data (all delta operations). Data is identified by serial number. The data header includes lot # and date of test.

• The Certification of Conformance is part of the shipping invoice and is not part of the data book. The Certificate of Conformance is signed

by an authorized quality representative.