Electronic Components Datasheet Search |
|
L6919CDTR Datasheet(PDF) 11 Page - STMicroelectronics |
|
L6919CDTR Datasheet(HTML) 11 Page - STMicroelectronics |
11 / 32 page 11/32 L6919C The BOOTx and VCCDR pins are separated from IC's power supply (VCC pin) as well as signal ground (SGND pin) and power ground (PGND pin) in order to maximize the switching noise immunity. The separated supply for the different drivers gives high flexibility in mosfet choice, allowing the use of logic-level mosfet. Several com- bination of supply can be chosen to optimize performance and efficiency of the application. Power conversion is also flexible; 5V or 12V bus can be chosen freely. The peak current is shown for both the upper and the lower driver of the two phases in figure 3. A 10nF capac- itive load has been used. For the upper drivers, the source current is 1.9A while the sink current is 1.5A with VBOOT -VPHASE = 12V; similarly, for the lower drivers, the source current is 2.4A while the sink current is 2A with VCCDR = 12V. CURRENT READING AND OVER CURRENT The current flowing trough each phase is read using the voltage drop across the low side mosfets RdsON or across a sense resistor (RSENSE) and internally converted into a current. The Tran conductance ratio is issued by the external resistor Rg placed outside the chip between ISENx and PGNDSx pins toward the reading points. The full differential current reading rejects noise and allows to place sensing element in different locations with- out affecting the measurement's accuracy. The current reading circuitry reads the current during the time in which the low-side mosfet is on (OFF Time). During this time, the reaction keeps the pin ISENx and PGNDSx at the same voltage while during the time in which the reading circuitry is off, an internal clamp keeps these two pins at the same voltage sinking from the ISENx pin the necessary current (Needed if low-side mosfet RdsON sense is implemented to avoid absolute maximum rating overcome on ISENx pin). The proprietary current reading circuit allows a very precise and high bandwidth reading for both positive and negative current. This circuit reproduces the current flowing through the sensing element using a high speed Track & Hold Tran conductance amplifier. In particular, it reads the current during the second half of the OFF time reducing noise injection into the device due to the mosfet turn-on (See fig. 5). Track time must be at least 200ns to make proper reading of the delivered current Figure 5. Current Reading Timing (Left) and Circuit (Right) This circuit sources a constant 50 µA current from the PGNDSx pin and keeps the pins ISENx and PGNDSx at the same voltage. Referring to figure 4, the current that flows in the ISENx pin is then given by the following equation: Where RSENSE is an external sense resistor or the rds,on of the low side mosfet and Rg is the transconductance resistor used between ISENx and PGNDSx pins toward the reading points; IPHASE is the current carried by each phase and, in particular, the current measured in the middle of the oscillator period The current information reproduced internally is represented by the second term of the previous equation as Rg 50 µµA IISENx Rg LGATEX ISENX PGNDSX ILS1 ILS2 Track & Hold Total current information I ISENx 50 µA R SENSE I PHASE ⋅ R g ---------------------------------------------- + 50 µAI IN FO x + == |
Similar Part No. - L6919CDTR |
|
Similar Description - L6919CDTR |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |