Electronic Components Datasheet Search |
|
ST24C01M1TR Datasheet(PDF) 3 Page - STMicroelectronics |
|
ST24C01M1TR Datasheet(HTML) 3 Page - STMicroelectronics |
3 / 16 page Mode RW bit MODE Bytes Initial Sequence Current Address Read ’1’ X 1 START, Device Select, RW = ’1’ Random Address Read ’0’ X1 START, Device Select, RW = ’0’, Address, ’1’ reSTART, Device Select, RW = ’1’ Sequential Read ’1’ X 1 to 128 Similar to Current or Random Mode Byte Write ’0’ X 1 START, Device Select, RW = ’0’ Multibyte Write (2) ’0’ VIH 4 START, Device Select, RW = ’0’ Page Write ’0’ VIL 8 START, Device Select, RW = ’0’ Notes: 1. X = VIH or VIL 2. Multibyte Write not available in ST24/25W01 versions. Table 4. Operating Modes (1) Device Code Chip Enable RW Bit b7 b6 b5 b4 b3 b2 b1 b0 Device Select 1 0 1 0 E2 E1 E0 RW Note: The MSB b7 is sent first. Table 3. Device Select Code When writing data to the memory it responds to the 8 bits received by asserting an acknowledge bit during the 9th bit time. When data is read by the bus master, it acknowledges the receipt of the data bytes in the same way. Data transfers are termi- nated with a STOP condition. Power On Reset: VCC lock out write protect. In order to prevent data corruption and inadvertent write operations during power up, a Power On Reset (POR) circuit is implemented. Until the VCC voltage has reached the POR threshold value, the internal reset is active, all operations are disabled and the device will not respond to any command. In the same way, when VCC drops down from the operating voltage to below the POR threshold value, all operations are disabled and the device will not respond to any command. A stable VCC must be applied before applying any logic signal. SIGNAL DESCRIPTIONS Serial Clock (SCL). The SCL input pin is used to synchronize all data in and out of the memory. A resistor can be connected from the SCL line to VCC to act as a pull up (see Figure 3). Serial Data (SDA). The SDA pin is bi-directional and is used to transfer data in or out of the memory. It is an open drain output that may be wire-OR’ed with other open drain or open collector signals on the bus. A resistor must be connected from the SDA bus line to VCC to act as pull up (see Figure 3). Chip Enable (E0 - E2). These chip enable inputs are used to set the 3 least significant bits (b3, b2, b1) of the 7 bit device select code. These inputs may be driven dynamically or tied to VCC or VSS to establish the device select code. Mode (MODE). The MODE input is available on pin 7 (see also WC feature) and may be driven dynami- cally. It must be at VIL or VIH for the Byte Write mode, VIH for Multibyte Write mode or VIL for Page Write mode. When unconnected, the MODE input is internally read as VIH (Multibyte Write mode). Write Control (WC). An hardware Write Control feature (WC) is offered only for ST24W01 and ST25W01 versions on pin 7. This feature is usefull to protect the contents of the memory from any erroneous erase/write cycle. The Write Control sig- nal is used to enable (WC = VIH) or disable (WC = VIL) the internal write protection. When uncon- nected, the WC input is internally read as VIL and the memory area is not write protected. 3/16 ST24/25C01, ST24C01R, ST24/25W01 |
Similar Part No. - ST24C01M1TR |
|
Similar Description - ST24C01M1TR |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |