STMPE1601_1 datasheet(13/61 Pages) STMICROELECTRONICS

Part #	STMPE1601

Description	16-bit enhanced port expander with keypad and PWM controller Xpander Logic

Download	61 Pages

Scroll/Zoom	100%

Manufacturer	STMICROELECTRONICS [STMicroelectronics]

Direct Link	http://www.st.com

Logo

13 / 61 page

STMPE1601

I2C interface

13/61

6.1

Minimizing current drain on I2C address lines

The GPIOs 13-15 are used as I2C address input during POR. Pull-up/down resistor of

500 K-1.5 M is recommended for these address lines. In the case that these pins are driven

to an opposite logic level during device operation, there would be a current drain of VIO/R.

This amounts to a significant current for portable devices.

To minimize the current drain on I2C lines, a few methods are recommended.

1.

If maximum keypad size is not required, these shared lines should not be used for

keypad operation.

2.

If the maximum keypad size is required, choose I2C address 0x40, as this requires that

all 3 address lines to be pulled to ground, minimizing the current drain in keypad

operation. In this mode of operation, the pull up/down resistors on the I2C lines should

be:

A reset circuit with longer RC is used to ensure enough time for the address lines to

settle to the final values.

3.

In system-controlled idle state, all keypad pins to be configured as hotkey with interrupt

enabled. If any key is pressed, system initiates keypad controller for scanning

operation.

Table 13.

Recommended pull up/down resistors on the I2C lines

VIO

1.8 V

2.5 V

3.3 V

Reset RC

or pulse width(1)

1.

Recommended values are chosen to minimize leakage current.

Note

RPU/RPD

1.5 M

1.2 M

1 M

270 K/0.47

μF

120 ms

All 3 address

lines are

used for

keypad

controller

RPU/RPD

1.0 M

800 K

660 K

180 K/0.47

μF

80 ms

2 address

lines are

used for

keypad

controller

RPU/RPD

500K

400K

330K

90K/0.47

μF

40 ms

1 address

line is used

for keypad

controller

Similar Part No. - STMPE1601_1

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	STMPE1601TBR	602Kb / 58P	16-bit enhanced port expander with keypad and PWM controller Xpander Logic

More results

Similar Description - STMPE1601_1

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	STMPE1601	602Kb / 58P	16-bit enhanced port expander with keypad and PWM controller Xpander Logic
	STMPE2403	890Kb / 63P	24-bit Enhanced port expander with Keypad and PWM controller Xpander logic
	STMPE2401	946Kb / 55P	24-bit Enhanced port expander with Keypad and PWM controller Xpander logic
	STMPE1801BJR	666Kb / 60P	Xpander Logic??18-bit enhanced port expander with keypad controller March 2011 Rev 3
	STMPE801	393Kb / 26P	8-bit port expander Xpander logic
	STMPE1600	280Kb / 27P	16-bit port expander with ultra-low power consumption Xpander Logic? February 2013 Rev 3
	STEVAL-TCS004V1	147Kb / 4P	16-bit port expander demonstration board with keypad and PWM controller based on the STMPE1601
	STMPE821	646Kb / 55P	8-bit Xpander Logic??with touchkey controller
	STEVAL-TCS001V1	228Kb / 4P	24 bit port expander demonstation board with LCD, keypad, and PWM interfaces based on the STMPE2401 December 2008 Rev 1
	STEVAL-TCS003V1	304Kb / 5P	24-bit port expander demonstration board with LCD, keypad, and PWM interfaces based on the STMPE2403 October 2009 Rev 1

More results

STMPE1601 Datasheet(PDF) 13 Page - STMicroelectronics

STMPE1601 Datasheet(HTML) 13 Page - STMicroelectronics

Similar Part No. - STMPE1601_1

Similar Description - STMPE1601_1

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61

Datasheet Download

Link URL