 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
PCA9635PW Datasheet(PDF) 2 Page - NXP Semiconductors |
|
||||||||||||||||||||||||||||||
PCA9635PW Datasheet(HTML) 2 Page - NXP Semiconductors |
|
|
2 / 35 page  PCA9635_6 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 06 — 11 September 2008 2 of 35 NXP Semiconductors PCA9635 16-bit Fm+ I2C-bus LED driver 2. Features I 16 LED drivers. Each output programmable at: N Off N On N Programmable LED brightness N Programmable group dimming/blinking mixed with individual LED brightness I 1 MHz Fast-mode Plus compatible I2C-bus interface with 30 mA high drive capability on SDA output for driving high capacitive buses I 256-step (8-bit) linear programmable brightness per LED output varying from fully off (default) to maximum brightness using a 97 kHz PWM signal I 256-step group brightness control allows general dimming (using a 190 Hz PWM signal) from fully off to maximum brightness (default) I 256-step group blinking with frequency programmable from 24 Hz to 10.73 s and duty cycle from 0 % to 99.6 % I Sixteen totem-pole outputs (sink 25 mA and source 10 mA at 5 V) with software programmable open-drain LED outputs selection (default at totem-pole). No input function. I Output state change programmable on the Acknowledge or the STOP Command to update outputs byte-by-byte or all at the same time (default to ‘Change on STOP’). I Active LOW Output Enable (OE) input pin. LED outputs programmable to logic 1, logic 0 or ‘high-impedance’ (default at power-up) when OE is HIGH, thus allowing hardware blinking and dimming of the LEDs. I 7 hardware address pins allow 126 devices to be connected to the same I2C-bus I 4 software programmable I2C-bus addresses (one LED Group Call address and three LED Sub Call addresses) allow groups of devices to be addressed at the same time in any combination (for example, one register used for ‘All Call’ so that all the PCA9635s on the I2C-bus can be addressed at the same time and the second register used for three different addresses so that 1 ⁄ 3 of all devices on the bus can be addressed at the same time in a group). Software enable and disable for I2C-bus address. I Software Reset feature (SWRST Call) allows the device to be reset through the I2C-bus I 25 MHz internal oscillator requires no external components I Internal power-on reset I Noise filter on SDA/SCL inputs I Edge rate control on outputs I No glitch on power-up I Supports hot insertion I Low standby current I Operating power supply voltage range of 2.3 V to 5.5 V I 5.5 V tolerant inputs I −40 °C to +85 °C operation I ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101 I Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA I Packages offered: TSSOP28 |
Similar Part No. - PCA9635PW |
|
Similar Description - PCA9635PW |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
