 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
TMS320VC5402PGE100 Datasheet(PDF) 10 Page - Texas Instruments |
|
|
||||||||||||||||||||||||||||||
TMS320VC5402PGE100 Datasheet(HTML) 10 Page - Texas Instruments |
|
|
10 / 68 page  TMS320VC5402 FIXEDPOINT DIGITAL SIGNAL PROCESSOR SPRS079E – OCTOBER 1998 – REVISED AUGUST 2000 10 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 Terminal Functions (Continued) TERMINAL NAME DESCRIPTION TYPE† TERMINAL NAME DESCRIPTION TYPE† HOST-PORT INTERFACE SIGNALS (CONTINUED) HBIL I Byte identification. HBIL identifies the first or second byte of transfer. The HBIL input has an internal pullup resistor that is only enabled when HPIENA = 0. HCS I Chip select. HCS is the select input for the HPI and must be driven low during accesses. The chip-select input has an internal pullup resistor that is only enabled when HPIENA = 0. HDS1 HDS2 I Data strobe. HDS1 and HDS2 are driven by the host read and write strobes to control transfers. The strobe inputs have internal pullup resistors that are only enabled when HPIENA = 0. HAS I Address strobe. Hosts with multiplexed address and data pins require HAS to latch the address in the HPIA register. HAS has an internal pullup resistor that is only enabled when HPIENA = 0. HR/W I Read/write. HR/W controls the direction of an HPI transfer. R/W has an internal pullup resistor that is only enabled when HPIENA = 0. HRDY O/Z Ready. The ready output informs the host when the HPI is ready for the next transfer. HRDY goes into the high-impedance state when OFF is low. HINT O/Z Host interrupt. This output is used to interrupt the host. When the DSP is in reset, HINT is driven high . HINT can also be configured as the timer 1 output (TOUT1), when the HPI is disabled. The signal goes into the high-impedance state when OFF is low. HPIENA I HPI module select. HPIENA must be driven high during reset to enable the HPI. An internal pulldown resistor is always active and the HPIENA pin is sampled on the rising edge of RS. If HPIENA is left open or is driven low during reset, the HPI module is disabled. Once the HPI is disabled, the HPIENA pin has no effect until the ’5402 is reset. SUPPLY PNS CVDD S +VDD. Dedicated 1.8-V power supply for the core CPU DVDD S +VDD. Dedicated 3.3-V power supply for the I/O pins VSS S Ground TEST PINS TCK I IEEE standard 1149.1 test clock. TCK is normally a free-running clock signal with a 50% duty cycle. The changes on the test access port (TAP) of input signals TMS and TDI are clocked into the TAP controller, instruction register, or selected test data register on the rising edge of TCK. Changes at the TAP output signal (TDO) occur on the falling edge of TCK. TDI I IEEE standard 1149.1 test data input pin with internal pullup device. TDI is clocked into the selected register (instruction or data) on a rising edge of TCK. TDO O/Z IEEE standard 1149.1 test data output. The contents of the selected register (instruction or data) are shifted out of TDO on the falling edge of TCK. TDO is in the high-impedance state except when the scanning of data is in progress. TDO also goes into the high-impedance state when OFF is low. TMS I IEEE standard 1149.1 test mode select. Pin with internal pullup device. This serial control input is clocked into the TAP controller on the rising edge of TCK. TRST I IEEE standard 1149.1 test reset. TRST, when high, gives the IEEE standard 1149.1 scan system control of the operations of the device. If TRST is not connected or is driven low, the device operates in its functional mode, and the IEEE standard 1149.1 signals are ignored. Pin with internal pulldown device. † I = input, O = output, Z = high impedance, S = supply ‡ All revisions of the ’5402 can be operated with an external clock source, provided that the proper voltage levels be driven on the X2/CLKIN pin. It should be noted that the X2/CLKIN pin is referenced to the device 1.8V power supply (CVDD), rather than the 3V I/O supply (DVDD). Refer to the recommended operating conditions section of this document for the allowable voltage levels of the X2/CLKIN pin. |
Similar Part No. - TMS320VC5402PGE100 |
|
Similar Description - TMS320VC5402PGE100 |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
