STM32F101X4 datasheet(15/73 Pages) STMICROELECTRONICS | Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers, ADC and 4 communication interfaces

Part #	STM32F101X4

Description	Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers, ADC and 4 communication interfaces

Download	73 Pages

Scroll/Zoom	100%

Manufacturer	STMICROELECTRONICS [STMicroelectronics]

Direct Link	http://www.st.com

Logo

15 / 73 page

STM32F101x4, STM32F101x6

Description

Doc ID 15058 Rev 3

15/74

2.3.6

External interrupt/event controller (EXTI)

The external interrupt/event controller consists of 19 edge detector lines used to generate

interrupt/event requests. Each line can be independently configured to select the trigger

event (rising edge, falling edge, both) and can be masked independently. A pending register

maintains the status of the interrupt requests. The EXTI can detect an external line with a

pulse width shorter than the Internal APB2 clock period. Up to 80 GPIOs can be connected

to the 16 external interrupt lines.

2.3.7

Clocks and startup

System clock selection is performed on startup, however the internal RC 8 MHz oscillator is

selected as default CPU clock on reset. An external 4-16 MHz clock can be selected, in

which case it is monitored for failure. If failure is detected, the system automatically switches

back to the internal RC oscillator. A software interrupt is generated if enabled. Similarly, full

interrupt management of the PLL clock entry is available when necessary (for example on

failure of an indirectly used external crystal, resonator or oscillator).

Several prescalers allow the configuration of the AHB frequency, the high-speed APB

(APB2) and the low-speed APB (APB1) domains. The maximum frequency of the AHB and

the APB domains is 36 MHz. See Figure 2 for details on the clock tree.

2.3.8

Boot modes

At startup, boot pins are used to select one of three boot options:

●

Boot from User Flash

●

Boot from System Memory

●

Boot from embedded SRAM

The boot loader is located in System Memory. It is used to reprogram the Flash memory by

using USART1. For further details please refer to AN2606.

2.3.9

Power supply schemes

●

VDD = 2.0 to 3.6 V: External power supply for I/Os and the internal regulator.

Provided externally through VDD pins.

●

VSSA, VDDA = 2.0 to 3.6 V: External analog power supplies for ADC, Reset blocks, RCs

and PLL (minimum voltage to be applied to VDDA is 2.4 V when the ADC is used).

VDDA and VSSA must be connected to VDD and VSS, respectively.

●

VBAT = 1.8 to 3.6 V: Power supply for RTC, external clock 32 kHz oscillator and backup

registers (through power switch) when VDD is not present.

For more details on how to connect power pins, refer to Figure 9: Power supply scheme.

2.3.10

Power supply supervisor

The device has an integrated power on reset (POR)/power down reset (PDR) circuitry. It is

always active, and ensures proper operation starting from/down to 2 V. The device remains

in reset mode when VDD is below a specified threshold, VPOR/PDR, without the need for an

external reset circuit.

The device features an embedded programmable voltage detector (PVD) that monitors the

VDD/VDDA power supply and compares it to the VPVD threshold. An interrupt can be

generated when VDD/VDDA drops below the VPVD threshold and/or when VDD/VDDA is higher

Similar Part No. - STM32F101X4

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	STM32F101X4	1Mb / 79P	Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers, ADC and 4 communication interfaces
STMicroelectronics	STM32F101X4	1Mb / 77P	Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers

More results

Similar Description - STM32F101X4

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	STM32F101T6U6A	1Mb / 79P	Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers, ADC and 4 communication interfaces
	STM32F101C4T6A	1Mb / 79P	Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers, ADC and 4 communication interfaces
	STM32F101C6T6	1Mb / 79P	Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers, ADC and 4 communication interfaces
	STM32F101R6T6	1Mb / 79P	Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers, ADC and 4 communication interfaces
	STM32F101X4	1Mb / 77P	Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers
	STM32F102X4	872Kb / 69P	Low-density USB access line, ARM-based 32-bit MCU with 16/32 KB Flash, USB FS interface, 5 timers, ADC & 5 communication interfaces
	STM32F102C6T6A	855Kb / 69P	Low-density USB access line, ARM-based 32-bit MCU with 16/32 KB Flash, USB FS interface, 5 timers, ADC & 5 communication interfaces
	STM32F101X8	999Kb / 81P	Medium-density access line, ARM-based 32-bit MCU with 64 or 128 KB Flash, 6 timers, ADC and 7 communication interfaces
	STM32F101RBH6	1Mb / 90P	Medium-density access line, ARM-based 32-bit MCU with 64 or 128 KB Flash, 6 timers, ADC and 7 communication interfaces
	STM32F101X8	1Mb / 85P	Medium-density access line, ARM-based 32-bit MCU with 64 or 128 KB Flash, 6 timers, ADC and 7 communication interfaces

More results

STM32F101X4 Datasheet(PDF) 15 Page - STMicroelectronics

STM32F101X4 Datasheet(HTML) 15 Page - STMicroelectronics

Similar Part No. - STM32F101X4

Similar Description - STM32F101X4

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73

Datasheet Download

Link URL