STM32F101X4 datasheet(16/73 Pages) STMICROELECTRONICS | Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers, ADC and 4 communication interfaces

Part No.	STM32F101X4

Description	Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers, ADC and 4 communication interfaces

Download	73 Pages

Scroll/Zoom	100%

Manufacturer	STMICROELECTRONICS [STMicroelectronics]

Direct Link	http://www.st.com

Logo

16 / 73 page

Description

STM32F101x4, STM32F101x6

16/74

Doc ID 15058 Rev 3

than the VPVD threshold. The interrupt service routine can then generate a warning

message and/or put the MCU into a safe state. The PVD is enabled by software.

Refer to Table 10: Embedded reset and power control block characteristics for the values of

VPOR/PDR and VPVD.

2.3.11

Voltage regulator

The regulator has three operation modes: main (MR), low power (LPR) and power down.

●

MR is used in the nominal regulation mode (Run)

●

LPR is used in the Stop mode

●

Power down is used in Standby mode: the regulator output is in high impedance: the

kernel circuitry is powered down, inducing zero consumption (but the contents of the

registers and SRAM are lost)

This regulator is always enabled after reset. It is disabled in Standby mode, providing high

impedance output.

2.3.12

Low-power modes

The STM32F101xx low-density access line supports three low-power modes to achieve the

best compromise between low power consumption, short startup time and available wakeup

sources:

●

Sleep mode

In Sleep mode, only the CPU is stopped. All peripherals continue to operate and can

wake up the CPU when an interrupt/event occurs.

●

Stop mode

Stop mode achieves the lowest power consumption while retaining the content of

SRAM and registers. All clocks in the 1.8 V domain are stopped, the PLL, the HSI RC

and the HSE crystal oscillators are disabled. The voltage regulator can also be put

either in normal or in low power mode.

The device can be woken up from Stop mode by any of the EXTI line. The EXTI line

source can be one of the 16 external lines, the PVD output or the RTC alarm.

●

Standby mode

The Standby mode is used to achieve the lowest power consumption. The internal

voltage regulator is switched off so that the entire 1.8 V domain is powered off. The

PLL, the HSI RC and the HSE crystal oscillators are also switched off. After entering

Standby mode, SRAM and register contents are lost except for registers in the Backup

domain and Standby circuitry.

The device exits Standby mode when an external reset (NRST pin), a IWDG reset, a

rising edge on the WKUP pin, or an RTC alarm occurs.

Note:

The RTC, the IWDG, and the corresponding clock sources are not stopped by entering Stop

or Standby mode.

2.3.13

DMA

The flexible 7-channel general-purpose DMA is able to manage memory-to-memory,

peripheral-to-memory and memory-to-peripheral transfers. The DMA controller supports

circular buffer management avoiding the generation of interrupts when the controller

reaches the end of the buffer.

Similar Part No. - STM32F101X4

Manufacturer	Part No.	Datasheet	Description
STMicroelectronics	STM32F101X4	1Mb / 79P	Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers, ADC and 4 communication interfaces
STMicroelectronics	STM32F101X4	1Mb / 77P	Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers

More results

Similar Description - STM32F101X4

Manufacturer	Part No.	Datasheet	Description
STMicroelectronics	STM32F101T6U6A	1Mb / 79P	Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers, ADC and 4 communication interfaces
	STM32F101C4T6A	1Mb / 79P	Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers, ADC and 4 communication interfaces
	STM32F101C6T6	1Mb / 79P	Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers, ADC and 4 communication interfaces
	STM32F101R6T6	1Mb / 79P	Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers, ADC and 4 communication interfaces
	STM32F101X4	1Mb / 77P	Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers
	STM32F102X4	872Kb / 69P	Low-density USB access line, ARM-based 32-bit MCU with 16/32 KB Flash, USB FS interface, 5 timers, ADC & 5 communication interfaces
	STM32F102C6T6A	855Kb / 69P	Low-density USB access line, ARM-based 32-bit MCU with 16/32 KB Flash, USB FS interface, 5 timers, ADC & 5 communication interfaces
	STM32F101X8	999Kb / 81P	Medium-density access line, ARM-based 32-bit MCU with 64 or 128 KB Flash, 6 timers, ADC and 7 communication interfaces
	STM32F101RBH6	1Mb / 90P	Medium-density access line, ARM-based 32-bit MCU with 64 or 128 KB Flash, 6 timers, ADC and 7 communication interfaces
	STM32F101X8	1Mb / 85P	Medium-density access line, ARM-based 32-bit MCU with 64 or 128 KB Flash, 6 timers, ADC and 7 communication interfaces

More results

STM32F101X4 Datasheet(PDF) 16 Page - STMicroelectronics

STM32F101X4 Datasheet(HTML) 16 Page - STMicroelectronics

Similar Part No. - STM32F101X4

Similar Description - STM32F101X4

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73

Datasheet Download

Link URL