Electronic Components Datasheet Search
  English  ▼


AT42QT1011 Datasheet(PDF) 7 Page - ATMEL Corporation

Part # AT42QT1011
Description  One-channel Touch Sensor IC
Download  18 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  ATMEL [ATMEL Corporation]
Direct Link  http://www.atmel.com
Logo ATMEL - ATMEL Corporation

AT42QT1011 Datasheet(HTML) 7 Page - ATMEL Corporation

Back Button AT42QT1011 Datasheet HTML 3Page - ATMEL Corporation AT42QT1011 Datasheet HTML 4Page - ATMEL Corporation AT42QT1011 Datasheet HTML 5Page - ATMEL Corporation AT42QT1011 Datasheet HTML 6Page - ATMEL Corporation AT42QT1011 Datasheet HTML 7Page - ATMEL Corporation AT42QT1011 Datasheet HTML 8Page - ATMEL Corporation AT42QT1011 Datasheet HTML 9Page - ATMEL Corporation AT42QT1011 Datasheet HTML 10Page - ATMEL Corporation AT42QT1011 Datasheet HTML 11Page - ATMEL Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 7 / 18 page
background image
Detect Integrator
It is desirable to suppress detections generated by electrical noise or from quick brushes with an
object. To accomplish this, the QT1011 incorporates a detect integration (DI) counter that
increments with each detection until a limit is reached, after which the output is activated. If no
detection is sensed prior to the final count, the counter is reset immediately to zero. In the
QT1011, the required count is four. In LP mode the device will switch to Fast mode temporarily
in order to resolve the detection more quickly; after a touch is either confirmed or denied the
device will revert back to normal LP mode operation automatically.
The DI can also be viewed as a “consensus filter” that requires four successive detections to
create an output.
Forced Sensor Recalibration
The QT1011 has no recalibration pin; a forced recalibration is accomplished when the device is
powered up or after the recalibration timeout. However, supply drain is low so it is a simple
matter to treat the entire IC as a controllable load; driving the QT1011's Vdd pin directly from
another logic gate or a microcontroller port will serve as both power and “forced recalibration”.
The source resistance of most CMOS gates and microcontrollers is low enough to provide direct
power without problem.
Drift Compensation
Signal drift can occur because of changes in Cx and Cs over time. It is crucial that drift be
compensated for, otherwise false detections, nondetections, and sensitivity shifts will follow.
Drift compensation (Figure 3-5) is performed by making the reference level track the raw signal
at a slow rate, but only while there is no detection in effect. The rate of adjustment must be
performed slowly, otherwise legitimate detections could be ignored. The QT1011 drift
compensates using a slew-rate limited change to the reference level; the threshold and
hysteresis values are slaved to this reference.
Once an object is sensed, the drift compensation mechanism ceases since the signal is
legitimately high, and therefore should not cause the reference level to change.
Figure 3-5.
Drift Compensation
S ignal
H ysteresis

Similar Part No. - AT42QT1011

ManufacturerPart #DatasheetDescription
ATMEL Corporation
AT42QT1011-MAH ATMEL-AT42QT1011-MAH Datasheet
290Kb / 25P
   Single-key QTouch짰 Touch Sensor IC
More results

Similar Description - AT42QT1011

ManufacturerPart #DatasheetDescription
ATMEL Corporation
AT42QT1010 ATMEL-AT42QT1010 Datasheet
264Kb / 20P
   One-channel Touch Sensor IC
AT42QT1012 ATMEL-AT42QT1012_10 Datasheet
369Kb / 28P
   One-channel Toggle-mode Touch Sensor IC with Power Management Functions
Asahi Kasei Microsystem...
AK4160 AKM-AK4160 Datasheet
448Kb / 40P
   16-channel Capacitive Touch Sensor IC
AK4161 AKM-AK4161 Datasheet
415Kb / 12P
   6-channel Capacitive Touch Sensor IC
AK4161EN AKM-AK4161EN Datasheet
617Kb / 11P
   6-channel Capacitive Touch Sensor IC
ATMEL Corporation
AT42QT2120 ATMEL-AT42QT2120 Datasheet
583Kb / 46P
   QTouch 12-channel Touch Sensor IC
AT42QT1060 ATMEL-AT42QT1060_14 Datasheet
456Kb / 36P
   Six-channel QTouch Touch Sensor IC
AT42QT1070 ATMEL-AT42QT1070 Datasheet
423Kb / 34P
   Seven-channel QTouch짰 Touch Sensor IC
AT42QT1070 ATMEL-AT42QT1070_14 Datasheet
423Kb / 34P
   Seven-channel QTouch Touch Sensor IC
AT42QT2100-AU ATMEL-AT42QT2100-AU Datasheet
478Kb / 44P
   QTouch Touch Sensor IC
More results

Html Pages

1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18 

Datasheet Download

Go To PDF Page

Link URL

Privacy Policy
Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com

Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com