Electronic Components Datasheet Search |
|
BD9862MUV-E2 Datasheet(PDF) 10 Page - Rohm |
|
BD9862MUV-E2 Datasheet(HTML) 10 Page - Rohm |
10 / 17 page Technical Note 10/16 BD9862MUV www.rohm.com 2010.03 - Rev.A © 2010 ROHM Co., Ltd. All rights reserved. ● Method to select the application parts 1) Setting of output voltage The output voltage VOUT is set by dividing the resistance of the external resistor. CH1,CH2:VOUT=1+R2/R1 CH3:VOUT=-((R4/R3)+Voffset) R1: Feedback resistor (GND side), R2: Feedback resistor (VOUT side), R3: Feedback resistor (VREF side), R4: Feedback resistor (VOUT side) 2) Setting of the output inductor The maximum current ILpeak that flows in the inductor is calculated by the sum of the average current I ― L and the maximum value of ripple current ⊿IL. ILpeak = I ― L + ⊿IL. Generally ⊿IL. is set to about 30% of I ― L. The average current I ― L and the ripple current ⊿IL. are calculated according to the following formulas. max out min in out max L I V V I out osc in out min in L V L f 2 V V V I ⊿ L: value of inductance fOSC: switching frequency Vinmax: maximum input voltage Vinmin: minimum input voltage Vout: set value of output voltage Please set in such a way thatILpeak (the rated value of inductor current) is not exceeded. If ILpeak exceeded, then the efficiency is lowered extremely and damage to the inductor is caused. Please set in such a way that a good margin is left because the inductance varies in value. 3) Setting of output capacitor The capacitance & ESR of the output capacitor is influenced a great deal by output voltage ripple. Moreover, PFM mode intentionally makes the switching intermittent, so the output voltage ripple becomes larger compared with PWM mode. Please use an appropriate capacitor according to the service condition. In addition, please be sure to connect a ceramic capacitor of 1µF to REGOUT terminal. It is assumed that this IC uses a multilayer ceramic capacitor. For small multilayer ceramic capacitors such as Size 1608 etc., its actual capacitance may be lower than its nominal one because of the voltage that is bypassed. Please check to confirm various characteristics such as DC bypass etc. before use. 4) Setting of flying capacitor Please set the capacitance of the flying capacitor of the start-up charge pump not to exceed 1/10 of the capacitance of the CPOUT output capacitor. If it is more than 1/10 of the capacitance, damage may be caused. 5) Setting of the input capacitor A bypass capacitor for input is necessary to the VBAT terminal. Due to input & output voltage, load and wiring pattern etc., the actual capacitance is different from the necessary one, so please carefully check to confirm. 6) Setting of CR for phase compensation The CR for phase compensation is varied due to the characteristics of the capacitor & inductor, which are used in the output part, the input & output voltage and the load current etc. The phase-compensation CR constant in a recommended circuit diagram is set according to the service conditions, but applications under other conditions than the various conditions mentioned will cause oscillation instability etc. Please contact our technical service department if any conditions are changed. 7) Setting of schottky diode in the output part Please use a schottky diode with an allowable current more than ILpeak for the output part. Furthermore, it is necessary that the maximum reverse voltage is more than output voltage. Generally speaking, more lower the forward voltage, the higher the efficiency. 8) Setting of UVLO voltage The VULO release voltage VUVLO can be set according to the following formula: VUVLO=1+R2/R1(R1=GND-side resistance R2=VBAT-side resistance) If you want to make the start-up of the IC to lag behind the rising edge of VBAT, connect a capacitor to the UVLOSET terminal and set the time constant. 9) Setting of oscillating frequency Oscillating frequency can be adjusted by a resistor connected to the RT terminal. The CH1 oscillating frequency fosc1 is determined by the formula shown below: fosc1=1/(8×10 -12×RRT+4×10-8) The frequency calculated by the formula shown above is a theoretical value, so please refer to the above-mentioned reference data「RT resistance vs. CH1 switching frequency characteristic」for actual frequency. |
Similar Part No. - BD9862MUV-E2 |
|
Similar Description - BD9862MUV-E2 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |