Introducing Panasonic’s latest breakthrough in wireless networking, the

NEW

PAN1326/1316 Series RF Modules featuring both Bluetooth Low Energy and

Bluetooth connectivity. This powerful new technology combination creates a low

cost, ultra-low power wireless networking solution for short range applications.

The Bluetooth Low Energy (BLE) standard is designed to reduce power

consumption by establishing very fast connections (few ms) and transferring

small amounts of data. Using these techniques, energy consumption is reduced

to a tenth of Classic Bluetooth. Bluetooth Low Energy devices can be put into a

sleep mode and activated for event activities such as sending files to a gateway,

PC or mobile phone. Furthermore, the maximum power consumption is less

than 15 mA and the average power consumption is about 1 uA. Thus, a small

coin cell – such as a CR2032 – is capable of powering a device for up to 10

years of operation.

The

NEW PAN1326/1316 Host Controlled Interface (HCI) Series also brings

Texas Instrument’s CC2564, to an easy-to-use module format. Panasonic’s tiny

modules are designed to accommodate PCBs pad pitch of 1.3mm and as little

as two layers for easy implementation and manufacture.

Product Performance:

• Best-in-class Bluetooth RF performance (Tx power,

Rx sensitivity, blocking)

• Fully Qualified Bluetooth v4.0 EDR

• Dimensions PAN1326: 9mm x 9.5mm x 1.8mm (width

x length x height)

• Dimensions PAN1316: 6.5mm x 9mm x 1.7mm (width

x length x height)

• Certifications: Bluetooth, FCC, IC and CE

• Operating Temperature Range: -20ºC to +70ºC

• Supply Voltage Range: 1.7 - 4.8V

• Profiles: SPP, A2DP and AVRCP

• Based upon TI’s CC2564

• Integrates with TI’s ultra low-power MSP430

microprocessor

• Very fast algorithm for both ACL and eSCO

• Supports Extended Range Tx power with 10dBm

typical output

• Low power scan method for page and inquiry scans

at 1/3rd normal power

PAN1326 and PAN1316 Part Numbers:

Part Numbers

Description

ENW-89823A2JF

PAN1326, CC2564, Bluetooth & Bluetooth Low Energy, HCI module, antenna

ENW-89823C2JF

PAN1316, CC2564, Bluetooth & Bluetooth Low Energy, HCI module, no antenna

Development and Evaluation Part Numbers:

Part Numbers

Description

ENW-89825A2JF

PAN1323ETU, Development Module for PAN1315, PAN1316, PAN1317, PAN1325, PAN1326, PAN1327

EVAL_PAN1323

EVAL_PAN1323, Development Kit for PAN1315, PAN1316, PAN1317, PAN1325, PAN1326, PAN1327

New

Product

Introduction

Copyright © 2011 Panasonic Corporation of North America.

All Rights Reserved. Specifications are subject to change without notice.

PAN1326NPI Rev. 1.0, FY11-075-XXX

www.panasonic.com/rfmodules

piccomponentsmarketing@us.panasonic.com

1-800-344-2112

Dual-Mode Wireless Bluetooth Connectivity and Bluetooth Low Energy

P

i

Design and Specifications are subject to change without notice. Ask the factory for technical specifications before purchase and/or use. If there is any doubt

regarding the safety of this product, kindly inform us immediately for technical consultation.

PAN1450 Rev. A

The PAN1450 provides wireless interface per the BT 1.2

specification. Interoperability and BT compliance testing have

been completed for the BT Chip ZV4301 from Zeevo, Inc. to

facilate rapid time-to-market.

The BT Chip incorporates a widely popular 32-bit ARM7TDMI

TM

CPU core with sufficient bandwidth to support a wide range of

embedded µController applications and the module provides

full ARM7 software development access.

The PAN1450 is manufactured in a 13,4 x 18,7 x 2,2 mm³

SMD package and the only external component needed is an

50 ohm antenna.

Any customizations for the software can be handled

with our recommended partners.

Overview

- Inquiry results with RSSI (1.2)

- Adaptive frequency hopping (AFH) enabled (1.2)

- High throughput (>600 kbps)

- Hold-, Park- and Sniffmode

- Up to 128 bit encryption

- Audio capability on an SCO channel

- Support for very low power modes - sleep and deep sleep

- All bluetooth data rates (up to 57,6/723,2Kbps)

User Interfaces

- Full-speed USB version 2.0 compliant

- Programmable baud rate UART (9,6 Kbps - 921,6 Kbps)

- Debug UART (DUART)

- 16 General Purpose I/O‘s (interruptible)

- PCM audio (1 channel)

- SPI and JTAG interface

Radio Features

- High sensitivity design (-86 dBm typ.)

- Integrated RF shield

- Class 2 module (0dBm typ. output power)

- One antenna port

FEATURES

OUTLINES - ENW89803J

P R O D U CT

QUAL

OO

TH

B01839

Bluetooth-Module PAN1450

New

Product

Introduction

NEW

Bluetooth

Low

Energy