SPECIFICATION

MODEL

DCVOLTAGE

RATEDCURRENT

CURRENTRANGE

RATEDPOWER

PEAKCURRENT

OUTPUT

VOLTAGE ADJ.RANGE

LINEREGULATION

LOADREGULATION

SETUP,RISETIME

HOLDUP TIME (Typ.)

VOLTAGERANGE

Note.7

FREQUENCY RANGE

EFFICIENCY (Typ.)

INPUT

INRUSHCURRENT (Typ.)

LEAKAGECURRENT

OVERTEMPERATURE

SAFETY STANDARDS

WORKINGTEMP.

Note.5

WORKINGHUMIDITY

STORAGETEMP.,HUMIDITY

DCOKREALY CONTACTRATINGS(max.)

CURRENTSHARING

TEMP.COEFFICIENT

VIBRATION

MTBF

DIMENSION

OTHERS

NOTE

PACKING

OVERLOAD

OVERVOLTAGE

ACCURRENT (Typ.)

1500ms,150ms/230VAC

3000ms,150ms/115VACatfullload

14ms/230VACatfullload

90~264VAC127~370VDC

47~63Hz

94%

0.94/230VAC0.99/115VACatfullload

5A/115VAC2.5A/230VAC

56~65V

40A/115VAC80A/230VAC

<0.6mA /240VAC

29~33V

Protectiontype:Shutdowno/pvoltage withauto-recoveryorre-powerontorecovery

105

5

(TSW:detectonheatsinkofpowerswitch)

Protectiontype:Shutdowno/pvoltage,recoversautomaticallyaftertemperaturegoesdown

UL508 TUVEN60950-1approved

,

CompliancetoEN55022(CISPR22)ClassB, EN61000-3-2,-3

-25~+70

(Referto"DeratingCurve")

60Vdc/0.3A,30Vdc/1A,30Vac/0.5A resistiveload

PleaseseetheFunctionManual

20~95%RHnon-condensing

-40~+85

,10~95%RH

0.03%/

(0~50

Component:10~500Hz,2G10min./1cycle,60min.eachalongX, Y,Zaxes;Mounting:CompliancetoIEC60068-2-6

112.9Khrsmin.MIL-HDBK-217F(25

)

CompliancetoEN61000-4-2,3,4,5,6,8,11,EN55024,EN61000-6-2(EN50082-2),EN61204-3,heavyindustrylevel,criteria A,

SEMIF47,GL approved

85.5*125.2*128.5mm(W*H*D)

1.6Kg;8pcs/13.8Kg/0.9CUFT

POWERFACTOR (Typ.)

SDR-480P-48

48V

10A

0~10A

480W

15A

120mVp-p

48~55V

1.0%

0.5%

1.0%

SDR-480P-24

24V

20A

0~20A

480W

30A

720W(3sec.)

100mVp-p

24~28V

1.2%

0.5%

1.0%

Features :

WITHSTANDVOLTAGE

ISOLATIONRESISTANCE

I/P-O/P:3KVACI/P-FG:1.5KVACO/P-FG:0.5KVAC

O/P-DCOK:0.5KVAC

I/P-O/P,I/P-FG,O/P-FG:>100MOhms/500VDC/25

/70%RH

ENVIRONMENT

SAFETY &

FUNCTION

EMC

(Note4)

PROTECTION

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25

of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets

EMC directives.

5. Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power.

In case the adjacent device is a heat source, 15mm clearance is recommended.

6. 3 seconds peak power max. and the average output power should not exceed the rate power.

7. Derating may be needed under low input voltage. Please check the derating curve for more details.

Current sharing up to 3840W(7+1)

High efficiency 94% and low power dissipation

150% peak load capability

Built-in active PFC function, PF>0.94

Protections: Short circuit / Overload / Over voltage / Over temperature

Cooling by free air convection

Built-in constant current limiting circuit

Can be installed on DIN rail TS-35/7.5 or 15

UL 508(industrial control equipment)approved

EN61000-6-2(EN50082-2) industrial immunity level

100% full load burn-in test

3 years warranty

Built-in DC OK relay contact

FileName:SDR-480P-SPEC2011-12-27

Normallyw

morethan3

andthenshutdowno/pvoltagewithauto-recovery

orkswithin110~150%ratedoutputpowerfor

seconds

>150%ratedpower,constantcurrentlimitingwithauto-recoverywithin2secondsandmaycausetoshutdownifover2seconds

480WSingleOutputIndustrialDINRAIL withPFCandParallelFunction

GL

PQ

S

E

M

I F

4

7

EMCIMMUNITY

EMCEMISSION